Lenze EVS93xx FlyingSaw - Manual (Page 136)

FlyingSaw
Appendix
 Prepared Solution Servo PLC / ECSxA 1.1 EN 11-14
Error
number
Error code Cause Remedy
30 LU DC-bus voltage has dropped below the
value set in code C0173/000 Check mains voltage.
Check mains contactor/fuses.
In case of DC supply: check power supply module.
A current-carrying motor phase has
failed Disconnect motor and measure windings.
Disconnect supply cable and check for continuity.
The current threshold is set too low Increase current threshold in code C0599/000.
32 LP1
This monitoring is not suitable for
- synchronous
servo motors
- Field frequencies above 480Hz
Deactivate monitoring using code C0597/000 = 3.
Ambient temperature too high (T
U
> 40°C
or 50°C, depending on device
type/power reduction)
Leave drive controller to cool down and provide
improved ventilation (control cabinet fan?).
Check ambient temperature in the control cabinet.
Heatsinks are heavily soiled Clean heatsinks and protect against renewed soiling.
50 OH
Mounting position of the drive controller Check the mounting position of the controller and the
stipulated minimum distances top and bottom.
51 OH1 Internal temperature > 90 degrees C Leave drive controller to cool down and provide
improved ventilation (control cabinet fan?).
Check ambient temperature in the control cabinet
Overtemperature detection by PTC/KTY:
motor too hot due to continuous
overload/ overcurrent Check drive dimensioning. 53 OH3
No PTC/KTY connected Connect PTC/KTY.
Deactivate the OH3 error using code C0583/000 = 3).
Ambient temperature too high (T
U
> 40°C
or 50°C, depending on device
type/power reduction)
Leave drive controller to cool down and provide
improved ventilation (control cabinet fan?)
Check ambient temperature in the control cabinet.
Heatsinks are heavily soiled Clean heatsinks and protect against renewed soiling.
Mounting position of the drive controller Check the mounting position of the controller and the
stipulated minimum distances top and bottom.
54 OH4
A value that is too low has been set in
the parameters using code C0122/000 Increase value in code C0122/000.
55 OH5 Temperature inside the controller >
C0124 Leave drive controller to cool down and provide
improved ventilation (control cabinet fan?).
Check ambient temperature in the control cabinet
Overtemperature detection by PTC/KTY:
motor too hot due to continuous
overload/ overcurrent Check drive dimensioning.
No PTC/KTY connected
Connect PTC/KTY.
Deactivate the OH7 error using code C0584/000 = 3).
57 OH7
A value that is too low has been set in
the parameters using code C0121/000 Increase value in code C0121/000.
Overtemperature detection by
temperature contact: motor too hot due
to continuous overload/ overcurrent Check drive dimensioning. 58 OH8
No temperature contact connected
Connect temperature contact to terminals T1/T2.
Deactivate the OH8 error using code C0585/000 = 3).
61 CE0 Malfunction on the transfer of control
commands over the AIF interface (e.g.
PROFIBUS DP) Fix automation module firmly.
Fasten automation module in place.
62 CE1 CAN-IN1 channel is not receiving any
data or is receiving erroneous data Check CAN bus cable (connector X4)
Check CAN terminating resistor (on the first and last
CAN station)
Check configuration of the CAN node sending on CAN-
IN1
Check power supply to the CAN node sending on CAN-
IN1
Check monitoring time in code C0357/001 and increase
if necessary
63 CE2 CAN-IN2 channel is not receiving any
data or is receiving erroneous data Check CAN bus cable (connector X4)
Check CAN terminating resistor (on the first and last
CAN station)
Check configuration of the CAN node sending on CAN-
IN2
Check power supply to the CAN node sending on CAN-
IN2
Check monitoring time in code C0357/002 and increase
if necessary