Honeywell DCP552 Mark II - Manual (Page 107)

7-8
Item code Item No.
User
settings
Settings and descriptions
Factory default
settings
PA 93 Auto-tuning (CH2) 93 0: AT not performed
1: standard AT performed on currently used PID group in
mode other than READY mode.
2: AT writing overshoot-proof PID values to currently used
PID groups in mode other than READY mode performed.
3: Standard AT performed on PID groups A1 to A7 in READY mode.
4: AT writing overshoot-proof PID values to PID groups
A1 to A7 in READY mode continuously performed.
[Description:]
Т-----У is displayed for models with CP compensation and setting cannot be performed.
0
PA 94 Auto-tuning MV lower limit
(CH2)
94 -5.0 to upper limit %
[Description:]
Т-----У is displayed for models with CP compensation and setting cannot be performed.
Valid when setup data C22 setting is set to 1, 3 or 5.
0.0
PA 95 Auto-tuning MV upper limit
(CH2)
95 Lower limit to +105%
[Description:]
Т-----У is displayed for models with CP compensation and setting cannot be performed.
Valid when setup data C22 setting is set to 1, 3 or 5.
100.0
PA 96 PID computation initialize
(CH2)
96 0: No initialization during advance processing and PID group change
1: Initializes during advance processing but not during PID group change
2: No initialization during advance processing but
initializes during PID group change
3: Initializes both during advance processing and PID group change
0
PA 97 CP computation
compensation
97 0: No compensation
1: compensates
[Description:]
Т-----У is displayed for models without CP compensation and setting cannot be performed.
0
PA 98 CP value (PV) display lower
limit value
98 0 to upper limit SPU (CH2)
[Description:]
Т-----У is displayed for models without CP compensation and setting cannot be performed.
0.000
PA 99 CP value (PV) display upper
limit value
99 lower limit to 4000 SPU (CH2)
[Description:]
Т-----У is displayed for models without CP compensation and setting cannot be performed.
4.000
PA 100 Gas constant 100 10.0 to 50.0 %
[Description:]
Т-----У is displayed for models without CP compensation and setting cannot be performed.
23.5
PA 101 CP computation compensation No. 1 compensation point 101 No. 1 compensation point : 0 SPU (CH2) (tied)
No. 2 to 9compensation point : 0 to +2000 SPU (CH2)
NO. 10 compensation point : 2000 SPU (CH2) (tied)
NO. 1 to 10 compensation amount
: -1000 to +1000 SPU (CH2)
[Description:]
бТ-----У is displayed for models without CP compensation
and setting cannot be performed.
бТ-----У is displayed when PA97 is set to 0 and setting
cannot be performed.
0.000
PA 102 CP computation compensation No. 1 compensation amount 102 0.000
PA 103 CP computation compensation No. 2 compensation point 103 0.200
PA 104 CP computation compensation No. 2 compensation amount 104 0.000
PA 105 CP computation compensation No. 3 compensation point 105 0.400
PA 106 CP computation compensation No. 3 compensation amount 106 0.000
PA 107 CP computation compensation No. 4 compensation point 107 0.600
PA 108 CP computation compensation No. 4 compensation amount 108 0.000
PA 109 CP computation compensation No. 5 compensation point 109
PA 110 CP computation compensation No. 5 compensation amount 110
PA 111 CP computation compensation No. 6 compensation point 111
PA 112 CP computation compensation No. 6 compensation amount 112
PA 113 CP computation compensation No. 7 compensation point 113
PA 114 CP computation compensation No. 7 compensation amount 114
PA 115 CP computation compensation No. 8 compensation point 115
PA 116 CP computation compensation No. 8 compensation amount 116
PA 117 CP computation compensation No. 9compensation point 117
PA 118 CP computation compensation No. 9compensation amount 118
PA 119 CP computation compensation No. 10 compensation point 119
PA 120 CP computation compensation No. 10 compensation amount 120
0.800
0.000
1.000
0.000
1.200
0.000
1.400
0.000
1.600
0.000
2.000
0.000
Chapter 7. PARAMETER SETUP