Rockwell Automation 1771-QDC, D17716.5.86(Passport) PLASTIC MOLDING MODULE - Manual (Page 132)

Load Initial Profile Values
Chapter 8
8-11
IPC15 N44:71 * EndĆof Segment 2 Position Setpoint Distance from MoldĆend 2
IPC16 N44:72 100 Segment 2 Time Setpoint Time 1
IPC17 N44:73 * Segment 3 Velocity Setpoint Velocity 4
IPC18 N44:74 * Segment 3 Pressure Setpoint Pressure 3
IPC19 N44:75 * EndĆof Segment 3 Position Setpoint Distance from MoldĆend 2
IPC20 N44:76 100 Segment 3 Time Setpoint Time 1
IPC21 N44:77 * Segment 4 Velocity Setpoint Velocity 4
IPC22 N44:78 * Segment 4 Pressure Setpoint Pressure 3
IPC23 N44:79 * EndĆof Segment 4 Position Setpoint Distance from MoldĆend 2
IPC24 N44:80 100 Segment 4 Time Setpoint Time 1
IPC25 N44:81 * Segment 5 Velocity Setpoint Velocity 4
IPC26 N44:82 * Segment 5 Pressure Setpoint Pressure 3
IPC27 N44:83 * EndĆof Segment 5 Position Setpoint Distance from MoldĆend 2
IPC28 N44:84 100 Segment 5 Time Setpoint Time 1
IPC29 N44:85 * Segment 6 Velocity Setpoint Velocity 4
IPC30 N44:86 * Segment 6 Pressure Setpoint Pressure 3
IPC31 N44:87 * EndĆof Segment 6 Position Setpoint Distance from MoldĆend 2
IPC32 N44:88 100 Segment 6 Time Setpoint Time 1
IPC33 N44:89 * Segment 7 Velocity Setpoint Velocity 4
IPC34 N44:90 * Segment 7 Pressure Setpoint Pressure 3
IPC35 N44:91 * EndĆof Segment 7 Position Setpoint Distance from MoldĆend 2
IPC36 N44:92 100 Segment 7 Time Setpoint Time 1
IPC37 N44:93 * Segment 8 Velocity Setpoint Velocity 4
IPC38 N44:94 * Segment 8 Pressure Setpoint Pressure 3
IPC39 N44:95 * EndĆof Segment 8 Position Setpoint Distance from MoldĆend 2
IPC40 N44:96 100 Segment 8 Time Setpoint Time 1
IPC41 N44:97 * Segment 9 Velocity Setpoint Velocity 4
IPC42 N44:98 * Segment 9 Pressure Setpoint Pressure 3
IPC43 N44:99 * EndĆof Segment 9 Position Setpoint Distance from MoldĆend 2
IPC44 N44:100 100 Segment 9 Time Setpoint Time 1
IPC45 N44:101 * Segment 10 Velocity Setpoint Velocity 4
IPC46 N44:102 * Segment 10 Pressure Setpoint Pressure 3
IPC47 N44:103 * EndĆof Segment 10 Position Setpoint Distance from MoldĆend 2
IPC48 N44:104 100 Segment 10 Time Setpoint Time 1
IPC49 N44:105 * Segment 11 Velocity Setpoint Velocity 4
IPC50 N44:106 * Segment 11 Pressure Setpoint Pressure 3
IPC51 N44:107 0 Profile Velocity Offset Velocity 4
IPC52 N44:108 0 Profile Pressure Offset Pressure 3
IPC57 N44:113 0 Ram Pressure Limit for PressureĆlimit Velocity Control Pressure 3
IPC58 N44:114 0 Start of Zone for PressureĆlimit Velocity Control Distance from MoldĆend 2
IPC59 N44:115 0 Time Delay for PressureĆlimit Velocity Control Time 6
IPC60 N44:116 1000 Time Limit for Transition Time 1
IPC61 N44:117 0 Ram (screw) Position for Transition Distance from MoldĆend 2
IPC62 N44:118 0 Ram (screw) Pressure for Transition Pressure 3
IPC64 N44:120 0 Start of Zone for Pressure Transition Distance from MoldĆend 2
1 Time 2 Distance from MCC13 (if not zero) or MCC09 3 Pressure 4 Velocity
00.00 to 99.99 seconds 00.00 to 99.99 inches 0000 to 9999 PSI 00.00 to 99.99 in/sec
6 Time 000.0 to 999.9 millimeters 000.0 to 999.9 Bar 000.0 to 999.9 mm/sec
00.00 to 00.99 seconds
* Refer to the appropriate section later in this chapter for information on this parameter