Rockwell Automation 1771-QDC, D17716.5.86(Passport) PLASTIC MOLDING MODULE - Manual (Page 282)

Enter Your Values Here
Blank Worksheets
Appendix A
A-37
Worksheet 8ĆD (continued)
Plastication Profile Block (PPC)
Control Word ProĆSet 600 Addr. Value Description Units
PPC10 N44:426 Segment 1 Pressure Setpoint Pressure 3
PPC11 N44:427 EndĆof Segment 1 Position Setpoint Distance from MoldĆend 2
PPC12 N44:428 Segment 1 Time Setpoint Time 1
PPC14 N44:430 Segment 2 Pressure Setpoint Pressure 3
PPC15 N44:431 EndĆof Segment 2 Position Setpoint Distance from MoldĆend 2
PPC16 N44:432 Segment 2 Time Setpoint Time 1
PPC18 N44:434 Segment 3 Pressure Setpoint Pressure 3
PPC19 N44:435 EndĆof Segment 3 Position Setpoint Distance from MoldĆend 2
PPC20 N44:436 Segment 3 Time Setpoint Time 1
PPC22 N44:438 Segment 4 Pressure Setpoint Pressure 3
PPC23 N44:439 EndĆof Segment 4 Position Setpoint Distance from MoldĆend 2
PPC24 N44:440 Segment 4 Time Setpoint Time 1
PPC26 N44:442 Segment 5 Pressure Setpoint Pressure 3
PPC27 N44:443 EndĆof Segment 5 Position Setpoint Distance from MoldĆend 2
PPC28 N44:444 Segment 5 Time Setpoint Time 1
PPC30 N44:446 Segment 6 Pressure Setpoint Pressure 3
PPC31 N44:447 EndĆof Segment 6 Position Setpoint Distance from MoldĆend 2
PPC32 N44:448 Segment 6 Time Setpoint Time 1
PPC34 N44:450 Segment 7 Pressure Setpoint Pressure 3
PPC35 N44:451 EndĆof Segment 7 Position Setpoint Distance from MoldĆend 2
PPC36 N44:452 Segment 7 Time Setpoint Time 1
PPC38 N44:454 Segment 8 Pressure Setpoint Pressure 3
PPC39 N44:455 EndĆof Segment 8 Position Setpoint Distance from MoldĆend 2
PPC40 N44:456 Segment 8 Time Setpoint Time 1
PPC42 N44:458 Segment 9 Pressure Setpoint Pressure 3
PPC43 N44:459 EndĆof Segment 9 Position Setpoint Distance from MoldĆend 2
PPC44 N44:460 Segment 9 Time Setpoint Time 1
PPC46 N44:462 Segment 10 Pressure Setpoint Pressure 3
PPC47 N44:463 EndĆof Segment 10 Position Setpoint Distance from MoldĆend 2
PPC48 N44:464 Segment 10 Time Setpoint Time 1
PPC50 N44:466 Segment 11 Pressure Setpoint Pressure 3
PPC52 N44:468 Profile Pressure Offset Pressure 3
PPC61 N44:477 Cushion Size Distance from MoldĆend 2
PPC62 N44:478 Shot Size Incremental Distance 4
1 Time 2 Distance from MCC13 (if not zero) or MCc09 3 Pressure 4 Distance from PPC61
00.00 to 99.99 Seconds 00.00 to 99.99 Inches 0000 to 9999 PSI 00.00 to 99.99 Inches
000.0 to 999.9 Millimeters 000.0 to 999.9 Bar 000.0 to 999.9 Millimeter
* Refer to the appropriate section later in this chapter for information on this parameter