Rockwell Automation 1771-QDC, D17716.5.86(Passport) PLASTIC MOLDING MODULE - Manual (Page 278)

Enter Your Values Here
Blank Worksheets
Appendix A
A-33
IPC17 N44:73 Segment 3 Velocity Setpoint Percent of Maximum Velocity 4
IPC18 N44:74 Segment 3 Pressure Setpoint Pressure 3
IPC19 N44:75 EndĆof Segment 3 Position Setpoint Incremental Distance 2
IPC20 N44:76 Segment 3 Time Setpoint Time 1
IPC21 N44:77 Segment 4 Velocity Setpoint Percent of Maximum Velocity 4
IPC22 N44:78 Segment 4 Pressure Setpoint Pressure 3
IPC23 N44:79 EndĆof Segment 4 Position Setpoint Incremental Distance 2
IPC24 N44:80 Segment 4 Time Setpoint Time 1
IPC25 N44:81 Segment 5 Velocity Setpoint Percent of Maximum Velocity 4
IPC26 N44:82 Segment 5 Pressure Setpoint Pressure 3
IPC27 N44:83 EndĆof Segment 5 Position Setpoint Incremental Distance 2
IPC28 N44:84 Segment 5 Time Setpoint Time 1
IPC29 N44:85 Segment 6 Velocity Setpoint Percent of Maximum Velocity 4
IPC30 N44:86 Segment 6 Pressure Setpoint Pressure 3
IPC31 N44:87 EndĆof Segment 6 Position Setpoint Incremental Distance 2
IPC32 N44:88 Segment 6 Time Setpoint Time 1
IPC33 N44:89 Segment 7 Velocity Setpoint Percent of Maximum Velocity 4
IPC34 N44:90 Segment 7 Pressure Setpoint Pressure 3
IPC35 N44:91 EndĆof Segment 7 Position Setpoint Incremental Distance 2
IPC36 N44:92 Segment 7 Time Setpoint Time 1
IPC37 N44:93 Segment 8 Velocity Setpoint Percent of Maximum Velocity 4
IPC38 N44:94 Segment 8 Pressure Setpoint Pressure 3
IPC39 N44:95 EndĆof Segment 8 Position Setpoint Incremental Distance 2
IPC40 N44:96 Segment 8 Time Setpoint Time 1
IPC41 N44:97 Segment 9 Velocity Setpoint Percent of Maximum Velocity 4
IPC42 N44:98 Segment 9 Pressure Setpoint Pressure 3
IPC43 N44:99 EndĆof Segment 9 Position Setpoint Incremental Distance 2
IPC44 N44:100 Segment 9 Time Setpoint Time 1
IPC45 N44:101 Segment 10 Velocity Setpoint Percent of Maximum Velocity 4
IPC46 N44:102 Segment 10 Pressure Setpoint Pressure 3
IPC47 N44:103 EndĆof Segment 10 Position Setpoint Incremental Distance 2
IPC48 N44:104 Segment 10 Time Setpoint Time 1
IPC49 N44:105 Segment 11 Velocity Setpoint Percent of Maximum Velocity 4
IPC50 N44:106 Segment 11 Pressure Setpoint Pressure 3
IPC51 N44:107 Profile Velocity Offset Percent of Maximum Velocity 4
IPC52 N44:108 Profile Pressure Offset Pressure 3
IPC57 N44:113 Ram Pressure Limit for PressureĆlimit Velocity Control Pressure 3
IPC58 N44:114 Min Ram Position for PressureĆlimit Velocity Control Incremental Distance 2
IPC59 N44:115 Time Delay for PressureĆlimit Velocity Control Time 1
IPC60 N44:116 Time Limit for Transition Time 1
IPC61 N44:117 Ram (screw) Position for Transition Incremental Distance 2
IPC62 N44:118 Ram (screw) Pressure for Transition Pressure 3
IPC63 N44:119 Cavity Pressure for Transition Pressure 3
IPC64 N44:120 Ram (screw) Position for Pressure Transition Inhibit Incremental Distance 2
1 Time 2 Axis Measured from MCC27 3 Pressure 4 Percent Signal Output
00.00 to 99.99 Seconds (is nonĆzero) or MCC23 0000. to 9999. PSI 00.00 to 99.99%
00.00 to 99.99 Inches 000.0 to 999.9 Bar
000.0 to 999.9 Millimeters
* Refer to the appropriate section later in this chapter for information on this parameter