Yaskawa AC Drive Z1000 AC Drive HVAC Fan - Manual (Page 335)

ov Suppression Function Selection........................................... 215
P
Password and Password Setting ................................................20
Peak Hold Current .............................................................. 236
Peak Hold Output Frequency ................................................. 236
Performance Life ............................................................... 166
Performance Life Monitors Maintenance Monitors........................ 166
Periodic Inspection ............................................................. 164
Periodic Maintenance .......................................................... 166
Phase Order Selection ............................................................28
Phase Order Selection (Emergency Override Reference Selection) ..... 153
Phase Order Selection (Emergency Override Speed) ...................... 153
PI2 Disable (N.O.) ................................................................81
PI2 Integral Hold..................................................................82
PI2 Integral Reset .................................................................81
PI2 Inverse Operation ............................................................81
PI Accel/Decel Time .............................................................44
PID Feedback High...............................................................90
PID Feedback Low ...............................................................90
PI Disable ..........................................................................77
PI Feedback...................................................................... 237
PI Feedback Function Selection ................................................46
PI Feedback High Detection Level .............................................43
PI Feedback High Detection Time .............................................43
PI Feedback Loss Detection Selection .........................................42
PI Feedback Low Detection Level .............................................43
PI Feedback Low Detection Time ..............................................43
PI Feedback Offset ...............................................................46
PI Function Setting ...............................................................40
PI Input (feedback) ............................................................. 237
PI Input Level Selection .........................................................78
PI Input Limit .....................................................................46
PI Integral Hold ...................................................................78
PI Integral Reset .........................................................78, 79, 81
PI Maximum Boost Time........................................................46
PI Monitors ...................................................................... 158
PI Offset Adjustment .............................................................40
PI Output......................................................................... 237
PI Output Gain Setting ...........................................................41
PI Output Level Selection .......................................................41
PI Output Limit ...................................................................40
PI Output Lower Limit...........................................................46
PI Output Monitor Calculation Method........................................47
PI Output Reverse Selection ....................................................41
PI Primary Delay Time Constant ...............................................40
PI Setpoint ....................................................................... 237
PI Setpoint Boost Setting ........................................................45
PI Setpoint Display Digits .......................................................47
PI Setpoint Monitor Unit Selection.............................................48
PI Setpoint Scaling ...............................................................45
PI Setpoint Selection .............................................................44
PI Setpoint User Display.........................................................47
PI Setpoint Value .................................................................44
PI Sleep Delay Time .............................................................44
PI Sleep Function Start Level ...................................................44
PI Sleep Input Source ............................................................45
PI Snooze Deactivation Level...................................................45
PI Snooze Delay Time ...........................................................45
PI Snooze Feedback Level ......................................................46
PI Snooze Level...................................................................45
PI Soft Starter Cancel ............................................................78
PI Square Root Gain..............................................................46
PI Unit Selection ..................................................................47
PM Motor Auto-Tuning Mode Selection .................................... 155
PM Motor Base Frequency .................................................... 156
PM Motor Control Tuning..................................................... 125
PM Motor d-Axis Inductance ................................................. 156
PM Motor Induced Voltage Constant ........................................ 156
PM Motor q-Axis Inductance ................................................. 156
PM Motor Rated Current ...................................................... 156
PM Motor Rated Power........................................................ 155
PM Motor Rated Voltage ...................................................... 155
PM Motor Stator Resistance .................................................. 156
PM Motor Type ................................................................. 155
Power Detection Filter Time ....................................................50
Present Value Access........................................................... 256
Previous Fault ................................................................... 233
Program Lockout .................................................................77
Programmable Bypass Logic.................................................. 144
Programmable Run Timers for Real Time Clock (RTC).................. 136
Proportional Gain Setting (P) ...................................................40
Pull-In Current ............................................................ 126, 220
Pull-In Current Compensation Time Constant.............................. 220
Pull-In Current Level for PM Motor Tuning................................ 157
R
Rated Current Depending on Carrier Frequency .............................55
READ ............................................................................ 132
Reading BACnet Drive Parameters .......................................... 261
Reading Drive MEMOBUS/Modbus Register Contents .................. 314
Real Time Clock ................................................................ 136
Real Time Clock Setting....................................................... 134
Reference Sample Hold ..........................................................77
Relay Operator Control ..........................................................91
Replacement Parts .............................................................. 166
Replacing the Drive ............................................................ 179
Reset Communication Parameters..............................................71
Response Messages from Drive to Master ...................... 255, 295, 311
Restart Enabled ...................................................................89
Reverse Jog ........................................................................76
Reverse Operation Selection ....................................................28
Reverse Operation Selection 2 by PI Output..................................48
Reverse Run Command for 2-Wire Seq. ......................................78
RS-422 Interface ................................................................ 306
RS-485 Interface .............................................. 249, 271, 287, 305
RTS Control Selection ............................................. 251, 289, 308
Run Command at Power Up.....................................................29
Run Command for 2-Wire Seq. 2...............................................78
Run Command Method Selection ................................ 252, 290, 309
RUN Command Selection for AUTO mode ................................ 187
Run Command Selection for AUTO Mode ...................................25
Run Command Selection in Programming Mode ............................28
Run Command Source ...........................................................86
Run Command Source Selection ............................................. 237
S
S: Special Parameters .................................................... 135, 224
S1: Dynamic Noise Control Function........................................ 224
S2: Sequence Timers ..................................................... 136, 224
Index
YASKAWA ELECTRIC SIEP YAIZ1U 03A YASKAWA AC Drive – Z1000 Programming Manual 335