Super Systems 9130 Series - Manual (Page 99)

Series 9130 Operations Manual Rev - 98
Temperature Value Column Atmosphere Value Column Option Value Column
MEVT_IN_0
Temperature Setpoint Event Mask
Event ON/OFF Bitmap
This opcode waits for multiple input events 0 through 15.
The Temperature Setpoint is an optional setpoint to send down. The range is -301 (disable) – 30000.
The Event Mask is the events to enable, which is the events affected. The options are: 0 – 15.
The Event ON/OFF Bitmap field will allow the user to select the bitmap for the event ON/OFF, which will set
the final condition of the events in the event mask. The opcode ignores the bits not in the enabled events
and waits on the bits specified in the bitmap. The options are: 0 – 15.
MEVT_IN_1
Temperature Setpoint Event Mask
Event ON/OFF Bitmap
This opcode waits for multiple input events 16 through 31.
The Temperature Setpoint is an optional setpoint to send down. The range is -301 (disable) – 30000.
The Event Mask is the events to enable, which is the events affected. The options are: 0 – 15.
Note – Even
though the events listed are 0 – 15, they correspond to 16 – 31 .
The Event ON/OFF Bitmap field will allow the user to select the bitmap for the event ON/OFF, which will set
the final condition of the events in the event mask. The opcode ignores the bits not in the enabled events
and waits on the bits specified in the bitmap. The options are: 0 – 15.
Note – Even though the events listed
are 0 – 15, they correspond to 16 – 31 .
MEVT_OUT_0
Temperature Setpoint Event Mask
Event ON/OFF Bitmap
This opcode will set multiple output events 0 through 15.
The Temperature Setpoint is an optional setpoint to send down. The range is -301 (disable) – 30000.
The Event Mask is the events to enable, which is the events affected. The options are: 0 – 15.
The Event ON/OFF Bitmap field will set the final condition of the events in the event mask. The opcode will
ignore the bits not in the mask and either set or reset the bits depending upon their states in the bitmap.
The options are: 0 – 15.
MEVT_OUT_1
Temperature Setpoint Event Mask
Event ON/OFF Bitmap
This opcode will set multiple output events 16 through 31.
The Temperature Setpoint is an optional setpoint to send down. The range is -301 (disable) – 30000.
The Event Mask is the events to enable, which is the events affected. The options are: 0 – 15.
Note – Even
though the events listed are 0 – 15, they correspond to 16 – 31 .
The Event ON/OFF Bitmap field will set the final condition of the events in the event mask. The opcode will
ignore the bits not in the mask and either set or reset the bits depending upon their states in the bitmap.
The options are: 0 – 15.
Note – Even though the events listed are 0 – 15, they correspond to 16 – 31 .
MEVT_OUT_2
Temperature Setpoint Event Mask
Event ON/OFF Bitmap
This opcode will set multiple output events 32 through 47.
The Temperature Setpoint is an optional setpoint to send down. The range is -301 (disable) – 30000.
The Event Mask is the events to enable, which is the events affected. The options are: 0 – 15.
Note – Even
though the events listed are 0 – 15, they correspond to 32 – 47 .
The Event ON/OFF Bitmap field will set the final condition of the events in the event mask. The opcode will
ignore the bits not in the mask and either set or reset the bits depending upon their states in the bitmap.
The options are: 0 – 15.
Note – Even though the events listed are 0 – 15, they correspond to 32 – 47 .