Lenze Drive PLC Developer Studio 9300 Servo PLC (V8.x) - Manual (Page 164)

9300 Servo PLC
Index
4−2
L
9300 Servo PLC EN 5.0
Encoder cable monitoring, 2−34
Error messages, 3−8
Causes and remedies, 3−13
causes and remedies, 3−13
Overview, 3−9
Responses, 3−12
Error sources, overview, 3−9
Extendability, 3−2
F
FAIL−QSP, 2−65 , 3−12
Fault analysis, 3−17
Fault memory, 3−17
Display in Global Drive Control, 3−18
Fault messages, causes and remedies, 3−13
Fault reset, 3−18
FCODE_FreeCode, 2−41
Feedback systems, 2−57
Field weakening, 2−56
File header, 3−6
FLASH memory, 3−3
Free codes, 2−41
G
Global Drive Control, Fault memory, 3−18
H
Heatsink temperature, Monitoring
Adjustable, 2−75
Fixed, 2−73
I
I x t overload
Monitoring, 2−67
Overcurrent diagram, 2−67
I² x t overload, Monitoring, 2−68
Inputs
Analog. Siehe Analog inputs
Definition, 1−6
Digital. Siehe Digital inputs
Inputs SYSTEM_FLAGS, 2−86
Inputs_AIF_Management, 2−15
Inputs_AIF1, 2−2
Inputs_AIF2, 2−7
Inputs_AIF3, 2−11
Inputs_ANALOG1, 2−18
Inputs_ANALOG2, 2−20
Inputs_DCTRL, 2−22
Inputs_DFIN, 2−28
Inputs_DFOUT, 2−35
Inputs_DIGITAL, 2−39
Inputs_MCTRL, 2−45
Inputs_MCTRL_AUX_HighResFeedback, 2−84
K
Keypad, status messages, 3−19
L
LECOM, status word C0150, 3−19
LED display, 3−19
LP1 − monitoring of the motor phases, 2−72
LU − undervoltage monitoring, 2−71
M
Master frequency input, 2−28
Master frequency output, 2−35
Maximum speed, 2−51
MCTRL_AUX_HighResFeedback (high−resolution encoder),
2−84
MCTRL_MotorControl (motor control), 2−44
Additional torque setpoint, 2−49
Current controller, 2−48
Feedback systems, 2−57
Field weakening, 2−56
Inputs_MCTRL, 2−45
Manual adaptation of motor data, 2−60
Maximum speed, 2−51
Monitoring, 2−62
LP1 − monitoring of the motor phases, 2−72
LU − undervoltage monitoring, 2−71
OC1 − earth−fault monitoring, 2−66
OC1 − short−circuit monitoring, 2−66
OC5 − I x t overload monitoring, 2−67
OC6 − I² x t overload monitoring, 2−68
OH − heatsink temperature monitoring (fixed), 2−73
OH3 − motor temperature monitoring (fixed), 2−74
OH4 − heatsink temperature monitoring (adjustable), 2−75
OH7 − motor temperature monitoring (adjustable), 2−76
OH8 − motor temperature monitoring via T1, T2, 2−77
OU − overvoltage monitoring, 2−69
PL − monitoring of the rotor position adjustment, 2−81
Response and effect on the drive, 2−65
Sd2 − resolver monitoring for open circuit, 2−78
monitoring
nErr − speed monitoring (speed out of tolerance margin),
2−82
NMAX − speed monitoring (maximum speed exceeded), 2−83
Sd6 − motor temperature sensor monitoring, 2−79
Sd7 − absolute value encoder monitoring, 2−79 , 2−80
Outputs_MCTRL, 2−47