Carrier AQUAFORCE 30XW150-400 User Manual
Page 8
8
This indicates an initialization period while the Navigator™
display initiates communication with the Main Base Board.
Once communication is established, the default rotating dis-
play will be shown. If communication is not established, the
Navigator module will display:
Communication
Failure
If the Navigator module is connected to a Main Base Board
without software loaded, the display will remain at the
powered-up initialization display.
Setting the Time and Date — The ComfortLink control has a
time and date function. This can be useful for diagnostics to de-
termine when alarms occur. The control is factory configured
for the proper date and for use in the Eastern Time Zone. The
control must be checked and corrected if necessary. The correct
time is important if the machine is to function on an internal
time schedule and display a proper time and date stamp for
alarms. The time and date will be displayed on the default ro-
tating display of the Navigator module. The time and date can
also be checked and changed under the Time Clock mode as
described below.
To change the time, press the arrow key to move to the cor-
rect hour and press
. The minutes can be changed in a
similar manner.
To check or change the date, the following items must be
checked and changed if necessary.
NOTE: WW is the current month of the controller, (01=January,
02=February, etc.).
XX is the current day of the month
YY is the day of the week, (01=Monday, 02-Tuesday, etc.)
ZZ is the year of the century, (06=2006, 07=2007)
Changing the Unit of Measure — The Navigator display has
two options for unit of measure on the display, English or SI
(metric). The factory default for the units of measure is
English. To change the unit of measure, the following item
must be changed.
Changing the Display Language — The Navigator display
has five language options to select from, English, Espanol,
Francais, Portugues, and Translated. The “Translated” option is
not supported at this time. The factory default language is
English. To change the display language, the following item
must be changed.
NOTE: When the Language Selection (Configuration
DISP LANG) variable is changed, all appropriate display
expansions will immediately change to the new language. The
four letter/digit code will not change. No power-off or control
reset is required when reconfiguring languages.
Adjusting the Contrast — The contrast of the display can be
adjusted to suit ambient conditions. To adjust the contrast, enter
the LED Test mode of the device.
Pressing
will access the TEST point. Pressing
again will cause the “OFF” to flash. Use the up or
down arrow to change “OFF” to “ON.” Pressing
will
illuminate all LEDs and display all pixels in the view screen.
Pressing
and
simultaneously allows the
user to adjust the display contrast. The display will read:
Adjust Contrast
- - - -+ - - - - - - - - - - - - - - -
Use the up or down arrows to adjust the contrast. The
screen’s contrast will change with the adjustment. Press
to accept the change. The Navigator module will
keep this setting as long as it is plugged in to the LEN (Local
Equipment Network) bus.
Adjusting the Backlight Brightness — The backlight of the
display can be adjusted to suit ambient conditions. The factory
default is set to the highest level. To adjust the backlight of the
Navigator module, enter the LED Test mode of the device.
Pressing
will access the TEST point. Pressing
again will cause the “OFF” to flash. Use the up or
down arrow to change “OFF” to “ON.” Pressing
will
illuminate all LEDs and display all pixels in the view screen.
Pressing the up and down arrow keys simultaneously allows
the user to adjust the display brightness. The display will read:
Adjust Brightness
- - - - - - - - - - - - - - - - - +
Use the up or down arrow keys to adjust screen brightness.
Press
to accept the change. The Navigator module
will keep this setting as long as it is plugged in to the LEN bus.
ITEM
ITEM EXPANSION
PATH
VALUE
HH.MM
Time of Day
Time Clock
TIME
XX.XX
ITEM
ITEM EXPANSION
PATH
VALUE
MNTH
Month of Year
Time Clock
DATE
WW
DOM
Day of Month
Time Clock
DATE
XX
DAY
Day of Week
Time Clock
DATE
YY
YEAR
Year of Century
Time Clock
DATE
ZZ
ITEM ITEM EXPANSION
PATH
VALUE
METR Metric Display
Configuration
DISP
OFF – English
ON – SI (Metric)
ITEM
ITEM EXPANSION
PATH
VALUE
LANG
Language Selection
Configuration
DISP
English
Espanol
Francais
Portugues
Translated
ENTER
ITEM
ITEM EXPANSION
PATH
VALUE
TEST
Test Display LEDs
Configuration
DISP
ITEM
ITEM EXPANSION
PATH
VALUE
TEST Test Display LED’s
Configuration Mode
DISP
ENTER
ENTER
ENTER
ENTER
ESCAPE
ENTER
ENTER
ENTER
ENTER
ENTER
Run Status
Service T
est
Temperatures
Pressures
Setpoints
Inputs
Outputs
Configuration
Time Clock
Operating Modes
Alarms
ENTER
ESC
MODE
Alarm Status
Comfor
t
Link
Fig. 7 — Navigator Display Module
a30-3924