Brocade Multi-Service IronWare Switching Configuration Guide (Supporting R05.6.00) - Manual (Page 134)

104 Multi-Service IronWare Switching Configuration Guide
53-1003036-02
Using LLDP
4
LLDP neighbors
The show lldp neighbors command displays a list of the current LLDP neighbors per port.
The following shows an example report.
Syntax: show lldp neighbors
The following table describes the information displayed by the show lldp neighbors command.
Neighbor entries
deleted The number of LLDP neighbors deleted since the last reboot or since the last time the
clear lldp statistics all command was issued. This number includes the number of
entries deleted after timing out or aging out.
Neighbor entries aged
out The number of LLDP neighbors dropped on all ports after the time-to-live expired.
Note that LLDP entries age out naturally when a port’s cable or module is disconnected
or when a port becomes disabled. However, if a disabled port is re-enabled, the system
will delete the old LLDP entries.
Neighbor
advertisements
dropped The number of valid LLDP neighbors the device detected, but could not add. This can
occur, for example, when a new neighbor is detected and the device is already
supporting the maximum number of neighbors possible. This can also occur when an
LLDPDU is missing a mandatory TLV or is not formatted correctly.
Port The local port number.
Tx Pkts Total The number of LLDP packets the port transmitted.
Rx Pkts Total The number of LLDP packets the port received.
Rx Pkts w/Errors The number of LLDP packets the port received that have one or more detectable errors.
Rx Pkts Discarded The number of LLDP packets the port received then discarded.
Rx TLVs Unrecognz The number of TLVs the port received that were not recognized by the LLDP local agent.
Unrecognized TLVs are retained by the system and can be viewed in the output of the
show LLDP neighbors detail command or retrieved through SNMP.
Rx TLVs Discarded The number of TLVs the port received then discarded.
Neighbors Aged Out The number of times a neighbor’s information was deleted because its TTL timer
expired.
This field... Displays...
Lcl Port The local LLDP port number.
Chassis ID The identifier for the device.
Brocade devices use the base MAC address of the device as the Chassis ID.
This field... Displays...
Brocade#show lldp neighbors
Lcl Port Chassis ID Port ID Port Description System Name
1 0004.1234.0fc0 0004.1234.0fc0 GigabitEthernet9/1 BigIron RX 32~
1 00e0.5201.4000 00e0.5201.4000 GigabitEthernet0/1/1 BigIron RX 4~
3 00e0.5211.0200 00e0.5211.0203 GigabitEthernet4 BigIron RX 4~
4 00e0.5211.0200 00e0.5211.0202 GigabitEthernet3 BigIron RX 16~
4 00e0.5211.0200 00e0.5211.0210 GigabitEthernet17 BigIron RX 4~
15 00e0.5211.0200 00e0.5211.020f GigabitEthernet16 BigIron RX 8~
16 00e0.5211.0200 00e0.5211.020e GigabitEthernet15 BigIron RX 16~
17 00e0.5211.0200 00e0.5211.0211 GigabitEthernet18 BigIron RX 4~
18 00e0.5211.0200 00e0.5211.0210 GigabitEthernet17 BigIron RX 4~