Brocade Multi-Service IronWare Switching Configuration Guide (Supporting R05.6.00) - Manual (Page 960)

930 Multi-Service IronWare Switching Configuration Guide
53-1003036-02
Configuring BFD for the specified protocol
25
Session Uptime: 0:1:37:50.600, LastSessionDownTimestamp: 0:0:0:0.0
Physical Port:TX: eth 1/1,RX: eth 1/1,Vlan Id: 3
NeighborAddress State Interface Holddown Interval R/H
10.100.100.100 UP ve 3 3000000 1000000 Y/M
Registered Protocols(Protocol/VRFID): bgp/0
Local: Disc: 27, Diag: 0, Demand: 0 Poll: 0
MinTxInterval: 1000000, MinRxInterval: 1000000, Multiplier: 3
Remote: Disc: 8, Diag: 0, Demand: 0 Poll: 0
MinTxInterval: 1000000, MinRxInterval: 1000000, Multiplier: 3
Stats: RX: 14232 TX: 12046 SessionUpCount: 1 at SysUpTime: 0:2:46:24.725
Session Uptime: 0:1:37:49.650, LastSessionDownTimestamp: 0:0:0:0.0
Physical Port:TX: eth 1/1,RX: eth 1/1,Vlan Id: 3
NeighborAddress State Interface Holddown Interval R/H
10.1.1.1 UP ve 3 3000000 1000000 Y/M
Registered Protocols(Protocol/VRFID): bgp/0
Local: Disc: 28, Diag: 0, Demand: 0 Poll: 0
MinTxInterval: 1000000, MinRxInterval: 1000000, Multiplier: 3
Remote: Disc: 9, Diag: 0, Demand: 0 Poll: 0
MinTxInterval: 1000000, MinRxInterval: 1000000, Multiplier: 3
Stats: RX: 15652 TX: 12044 SessionUpCount: 1 at SysUpTime: 0:2:46:24.725
Session Uptime: 0:1:37:48.725, LastSessionDownTimestamp: 0:0:0:0.0
Physical Port:TX: eth 1/1,RX: eth 1/1,Vlan Id: 3
NeighborAddress State Interface Holddown Interval R/H
10.102.102.100 UP ve 3 3000000 1000000 Y/M
Registered Protocols(Protocol/VRFID): bgp/0
Local: Disc: 29, Diag: 0, Demand: 0 Poll: 0
MinTxInterval: 1000000, MinRxInterval: 1000000, Multiplier: 3
Remote: Disc: 10, Diag: 0, Demand: 0 Poll: 0
MinTxInterval: 1000000, MinRxInterval: 1000000, Multiplier: 3
Stats: RX: 14232 TX: 12044 SessionUpCount: 1 at SysUpTime: 0:2:46:24.725
Session Uptime: 0:1:37:48.550, LastSessionDownTimestamp: 0:0:0:0.0
Physical Port:TX: eth 1/1,RX: eth 1/1,Vlan Id: 3
Brocade#
The following example illustrates the output from the show bfd neighbor bfd detail command for
the CES series and CER series devices.
Brocade#show bfd neighbor detail
Total Entries:1 R:RXRemote(Y:Yes/N:No)H:Hop(S:Single/M:Multi)
NeighborAddress State Interface Holddown Interval R/H
fe80::224:38ff:fe79:9310 UP eth 1/17 1500000 500000 Y/S
Registered Protocols(Protocol/VRFID): bgp/0
Local: Disc: 8, Diag: 0, Demand: 0 Poll: 0
MinTxInterval: 500000, MinRxInterval: 500000, Multiplier: 3
Remote: Disc: 2, Diag: 0, Demand: 0 Poll: 0
MinTxInterval: 500000, MinRxInterval: 500000, Multiplier: 3
Stats: RX: 160394 TX: 142648 SessionUpCount: 1 at SysUpTime: 5:17:14:13.225
Session Uptime: 0:17:49:42.100, LastSessionDownTimestamp: 0:0:0:0.0
Physical Port:TX: eth 1/17,RX: eth 1/17,Vlan Id: 1
Using PBIF Assist: Y
Brocade#
Syntax: show bfd neighbor bgp [ipv4-address | ipv6-address| detail]
The ipv4-address | ipv6-address options display BFD neighbor information for the BGP specified
IPv4 or IPv6 neighbor only.
The detail option displays BFD neighbor information for all BGP neighbors.
This display contains the following information.