Rockwell Automation 1336T PLC Comm. Adapter, Series B, FRN 2.xx-3.xx - Manual (Page 272)

Index I–4
Publication 1336 FORCE–5.13 –– September, 1998
Channel B Warning Status, 6–45
Clear Fault Command, 6–36
Clear Fault Owner, 6–29
conventions, 6–11
cross reference by name, 10–8
cross reference by number, 6–2, 10–6
Data Input A1, 6–13
Data Input A2, 6–13
Data Input B1, 6–13
Data Input B2, 6–14
Data Input C1, 6–14
Data Input C2, 6–14
Data Input D1, 6–14
Data Input D2, 6–14
Data Output A1, 6–21
Data Output A2, 6–21
Data Output B1, 6–21
Data Output B2, 6–21
Data Output C1, 6–21
Data Output C2, 6–22
Data Output D1, 6–22
Data Output D2, 6–22
definition of sink, P–6
definition of source, P–6
DIP Fault Setup, 6–43
Direction Mask, 6–35
Direction Owner, 6–28
Flux Owner, 6–29
Jog Mask, 6–36
Jog1 Owner, 6–28
Jog2 Owner, 6–28
Language Select, 6–13
listing by files and groups, 6–4– 6–10
Local Mask, 6–36
Local Owner, 6–29
Logic Command, 5–1
PLC Communications Board Status,
6–13
Port Enable, 6–35
pre–configured links, 2–14
Ramp Owner, 6–29
Redundant Channel Number, 6–40
Reference Mask, 6–36
Reset Drive Mask, 6–36
SCANport Default Reference, 6–37
Set Reference Owner, 6–28
SP Analog Input, 5–10, 6–20
SP Analog Output, 5–10, 6–30
SP Analog Select, 5–10, 6–31
SP Communication Retries, 6–12
SP Fault Selection, 6–45
SP Fault Status, 6–46
SP Warning Selection, 6–45
SP Warning Status, 6–46
Start Mask, 6–35
Start Owner, 6–28
Stop Owner, 6–27
Trend 1 Continuous Trigger, 6–48
Trend 1 Operand Parameter X, 6–46
Trend 1 Operand Parameter Y, 6–47
Trend 1 Operator, 6–47
Trend 1 Post Samples, 6–47
Trend 1 Sample Rate, 6–47
Trend 1 Select, 6–48
Trend 1 Status, 6–48
Trend 2 Continuous Trigger, 6–50
Trend 2 Operand Parameter X, 6–49
Trend 2 Operand Parameter Y, 6–49
Trend 2 Operator, 6–49
Trend 2 Post Samples, 6–50
Trend 2 Sample Rate, 6–50
Trend 2 Select, 6–50
Trend 2 Status, 6–50
Trend 3 Continuous Trigger, 6–52
Trend 3 Operand Parameter X, 6–51
Trend 3 Operand Parameter Y, 6–51
Trend 3 Operator, 6–52
Trend 3 Post Samples, 6–52
Trend 3 Sample Rate, 6–52
Trend 3 Select, 6–53
Trend 3 Status, 6–53
Trend 4 Continuous Trigger, 6–55
Trend 4 Operand Parameter X, 6–54
Trend 4 Operand Parameter Y, 6–54
Trend 4 Operator, 6–54
Trend 4 Post Samples, 6–55
Trend 4 Sample Rate, 6–54
Trend 4 Select, 6–55
Trend 4 Status, 6–55
Trend Input 1, 6–46
Trend Input 2, 6–49
Trend Input 3, 6–51
Trend Input 4, 6–53
Trend Output 1, 6–48
Trend Output 2, 6–51
Trend Output 3, 6–53
Trend Output 4, 6–56
Trim Owner, 6–29
PLC Communications Adapter Board
displaying the current firmware version,
6–12
example of system communications,
5–14
mounting, 1–2
photograph, 1–1
rate of discrete data transfer to drive, 3–2
RIO status word, 3–10
selecting board language, 6–13
status parameter, 6–13
troubleshooting, 8–1– 8–15
using system resources, 5–14
post samples for trends, 9–7
protocol selection, 2–2