HP 30 HP30 - Manual (Page 64)

Chapter 5 - Parameter List
5-4
Keypad Display Setting Range
Code Description
LCD 7-Segment LCD 7-Segment
Units
Factory
Default
Adj.
During
Run
Page
FU1-25 High Limit Frequency F-limit Hi 25 FU1-24 to FU1-20 0.01 60.00 [Hz] No
Manual 0
FU1-26
Manual/Auto Torque
Boost Selection
Torque boost 26
Auto 1
- Manual No 6-2
FU1-27
Torque Boost in Forward
Direction
Fwd boost 27 0 to 15 [%] 0.1 2.0 [%] No
FU1-28
Torque Boost in Reverse
Direction
Rev boost 28 0 to 15 [%] 0.1 2.0 [%] No
6-2
Linear 0
Square 1 FU1-29 Volts/Hz Pattern V/F pattern 29
User V/F 2
- Linear No 6-2
FU1-30 15 User V/F – Frequency 1 User freq 1 30 0 to FU1-20 0.01 15.00 [Hz] No
FU1-31 User V/F – Voltage 1 User volt 1 31 0 to 100 [%] 1 25 [%] No
FU1-32 User V/F – Frequency 2 User freq 2 32 0 to FU1-20 0.01 30.00 [Hz] No
FU1-33 User V/F – Voltage 2 User volt 2 33 0 to 100 [%] 1 50 [%] No
FU1-34 User V/F – Frequency 3 User freq 3 34 0 to FU1-20 0.01 45.00 [Hz] No
FU1-35 User V/F – Voltage 3 User volt 3 35 0 to 100 [%] 1 75 [%] No
FU1-36 User V/F – Frequency 4 User freq 4 36 0 to FU1-20 0.01 60.00 [Hz] No
FU1-37 User V/F – Voltage 4 User volt 4 37 0 to 100 [%] 1 100 [%] No
6-2
FU1-38
Output Voltage
Adjustment
Volt control 38 40 to 110 [%] 0.1 100.0 [%] No 6-2
FU1-39 Energy Save Level Energy save 39 0 to 30 [%] 1 0 [%] Yes 6-2
No 0
FU1-50
Electronic Thermal
Selection
ETH select 50
Yes 1
- No Yes
FU1-51 16
Electronic Thermal Level
for 1 Minute
ETH 1 min 51 FU1-52 to 200 [%] 1 150 [%] Yes
FU1-52
Electronic Thermal Level
for Continuous
ETH cont 52 50 to FU1-51 1 100 [%] Yes
Self-cool 0
FU1-53
Electronic Thermal
Characteristic Selection
(Motor Type)
Motor type 53
Forced-cool 1
- Self-cool Yes
6-2
FU1-54 Overload Warning Level OL level 54 30 to 150 [%] 1 150 [%] Yes
FU1-55
Overload Warning Hold
Time
OL time 55 0 to 30 [sec] 0.1 10.0 [sec] Yes
6-2
No 0
FU1-56 Overload Trip Selection OLT select 56
Yes 1
- Yes Yes
FU1-57 Overload Trip Level OLT level 57 30 to 150 [%] 1 180 [%] Yes
FU1-58 Overload Trip Delay Time OLT time 58 0 to 60 [sec] 1 60.0 [sec] Yes
6-2
FU1-59
Stall Prevention Mode
Selection
Stall prev. 59
000 to 111
(Bit Set)
bit 000 No
FU1-60 Stall Prevention Level Stall level 60 30 to 250 [%] 1 180 [%] No
6-2
15 Code FU1-30 through FU1-37 appears only when FU1-29 is set to ‘User V/F’.
16 Code FU1-51 through FU1-53 appears only when FU1-50 is set to ‘Yes’.