Yokogawa YVP110 - Manual (Page 69)

<11. Resource Block>
11-4
IM 21B04C01-01E
Table 11.5 DEVICE_STATUS_2 (with /EE)
Hexadecimal
Indication
Indication
when Device
Description is
installed.
Meaning
0x80000000
0x40000000
0x20000000
0x10000000
PID2 BLOCK_
ERR
not Zero
Block Error has occurred in
the PID2 block.
0x08000000 PID2 in Bypass
active
Bypass is activated in PID2
block.
0x04000000 PID2 O/S mode PID2 block is in O/S mode.
0x02000000 TB TRAVEL_
CALIB_RESULT
not Succeeded
Travel Calibration has not
been succeeded.
0x01000000 TB AUTO_
TUNE_RESULT
not Succeeded
Auto tuning has not been
succeeded.
0x00800000 AR BLOCK_ERR
not Zero
Block Error has occurred in
the AR block.
0x00400000 IS BLOCK_ERR
not Zero
Block Error has occurred in
the IS block.
0x00200000 OS BLOCK_ERR
not Zero
Block Error has occurred in
the OS block.
0x00100000 PID1 BLOCK_
ERR not Zero
Block Error has occurred in
the PID block.
0x00080000 DI2 BLOCK_ERR
not Zero
Block Error has occurred in
the DI2 block.
0x00040000 DI1 BLOCK_ERR
not Zero
Block Error has occurred in
the DI1 block.
0x00020000 AO BLOCK_ERR
not Zero
Block Error has occurred in
the AO block.
0x00010000 TB XD_ERROR
not Zero
XD Error has occurred in
the Transducer block.
0x00008000 TB in Signature
executing
Signature is proceeding.
0x00004000
0x00002000
0x00001000
PID1 in Bypass
active
Bypass is activated in PID
block.
0x00000800 DI2 in Simulate
active
SIMULATE is activated in
DI2 block.
0x00000400 DI1 in Simulate
active
SIMULATE is activated in
DI1 block.
0x00000200 AO in Simulate
active
SIMULATE is activated in
AO block.
0x00000100 TB in Auto tuning Auto tuning is proceeding.
0x00000080 AR in O/S mode AR block is in O/S mode.
0x00000040 IS in O/S mode IS block is in O/S mode.
0x00000020 OS in O/S mode OS block is in O/S mode.
0x00000010 PID1 in O/S mode PID block is in O/S mode.
0x00000008 DI2 in O/S mode DI2 block is in O/S mode.
0x00000004 DI1 in O/S mode DI1 block is in O/S mode.
0x00000002 AO in O/S mode AO block is in O/S mode.
0x00000001 TB in O/S mode TB block is in O/S mode.
Table 11.6 DEVICE_STATUS_3
Hexadecimal
Indication
Indication when
Device Description is
installed.
Meaning
0x80000000
0x40000000
0x20000000
0x10000000
0x08000000
0x04000000
0x02000000
0x01000000
0x00800000
0x00400000
0x00200000
0x00100000
0x00080000
0x00040000
0x00020000
0x00010000
0x00008000
Servo output drift
warning
Shows the contents of
the XD_ERROR in the
transducer block.
Refer to 12.6.1 XD_
ERROR for details.
0x00004000 A/D Converter failure
0x00002000 Position sensor failure
0x00001000 Deviation error
0x00000800 Severe servo output
drift
0x00000400 Pressure sensor
failure
0x00000200 Temperature sensor
failure
0x00000100 Deviation warning
0x00000080 Position sensor out of
range
0x00000040 Pressure sensor out
of range
0x00000020 Temperature sensor
out of range
0x00000010 Total near close limit
exceed
0x00000008 Total close limit
exceed
0x00000004 Total open limit
exceed
0x00000002 Travel limit exceed
0x00000001 Cycle count limit
exceed