Document Outline

• mn-CDM570-570L_r12.pdf
  • INSIDE COVER
  • TABLE OF CONTENTS
  • TABLES
  • FIGURES
  • PREFACE
    • About this Manual
      • Reporting Comments or Suggestions Concerning this Manual
    • Conventions and References
      • Patents and Trademarks
      • Warnings, Cautions, and Notes
      • Examples of Multi-Hazard Notices
      • Metric Conversion
      • Recommended Standard Designations
    • Safety and Compliance
      • Electrical Safety and Compliance
      • Electrical Installation
      • Fuses
      • Operating Environment
      • European Union Radio Equipment and Telecommunications Terminal Equipment (R&TTE) Directive (1999/5/EC) and EN 301 489-1
        • European Union Electromagnetic Compatibility (EMC) Directive (2004/108/EC)
        • European Union Low Voltage Directive (LVD) (2006/95/EC)
        • European Union RoHS Directive (2002/95/EC)
        • European Union Telecommunications Terminal Equipment Directive (91/263/EEC)
        • CE Mark
    • Warranty Policy
      • Limitations of Warranty
      • Exclusive Remedies
    • Getting Help
      • Contacting Comtech EF Data
      • Returning a Product for Upgrade or Repair
  • Chapter 1. INTRODUCTION
    • 1.1 Overview
    • 1.2 Functional Description
    • 1.3 Features
      • 1.3.1 Physical Description
      • 1.3.2 Compatibility
      • 1.3.3 Major Assemblies
      • 1.3.4 Dimensional Envelope
      • 1.3.5 Physical Features
        • 1.3.5.1 Front Panel
        • 1.3.5.2 Rear Panel
      • 1.3.6 Hardware Options
      • 1.3.7 Data Interfaces
      • 1.3.8 Verification
      • 1.3.9 AUPC
      • 1.3.10 EDMAC
      • 1.3.11 Updating Modem Firmware
      • 1.3.12 Fully Accessible System Topology (FAST)
      • 1.3.13 Supporting Hardware and Software
    • 1.4 Summary of Specifications
  • Chapter 2. INSTALLATION and STARTUP
    • 2.1 Unpacking and Inspecting the Shipment
    • 2.2 Rack-mounting the CDM-570/570L
      • 2.2.1 Installing the Optional Rear-Mounting Support Brackets Kit
    • 2.3 Initial Configuration
    • 2.4 Verifying Operation (IF Loopback Test)
    • 2.5 Connecting External Cables
  • Chapter 3. REAR PANEL CONNECTORS and PINOUTS
    • 3.1 Connector Overview
    • 3.2 IF Connections
      • 3.2.1 Rx IF Connectors
      • 3.2.2 Tx IF Connectors
    • 3.3 IF Connections
      • 3.3.1 Data Interface Connector, DB-25F
      • 3.3.2 G.703 Connections
        • 3.3.2.1 G.703 Balanced E1/T1 Interface Connector, DB-15F
        • 3.3.2.2 G.703 E1/T1 RJ-48 Connection via G.703 Balanced Interface Connector
        • 3.3.2.3 G.703 Unbalanced Interface Connectors (Tx/Rx), 75Ω BNC
      • 3.3.3 10/100 BaseT Ethernet Connections
        • 3.3.3.1 10/100 BaseT Ethernet Management (M&C) Port, RJ-45 (Standard)
        • 3.3.3.2 10/100 BaseT Ethernet Traffic Port, RJ-45 (with Optional IP Module only)
    • 3.4 Utility Connections
      • 3.4.1 Remote Control Interface Connector, DB-9M
      • 3.4.2 Form-C Traffic Alarms Connector, DB-15M
      • 3.4.3 1:1 Control Interface Connector, DB-9F
      • 3.4.4 Ext Ref Connector, BNC
      • 3.4.5 Async- Serial Console, RJ-11 (with Optional IP Module only)
    • 3.5 Power and Ground Connections
      • 3.5.1 Alternating Current (AC) Power Connector (Standard)
      • 3.5.2 Optional Direct Current (DC) Power Connector
        • 3.5.2.1 24 V or 48V DC Units – CDM-570 or CDM-570L Units
        • 3.5.2.2 48 V DC Units – CDMR-570L Unit Only
      • 3.5.3 Ground Connector
  • Chapter 4. UPDATING FIRMWARE
    • 4.1 Updating Firmware via Internet
    • 4.2 About Firmware Files, Naming, Versions and Formats
    • 4.3 Preparation for the Base Modem Ethernet FTP Upload Procedure
    • 4.4 Base Modem Bulk Firmware Update – Ethernet FTP Upload Procedure
    • 4.5 Ethernet IP Module FTP Upload Procedure
    • 4.6 USB Procedure
  • Chapter 5. FRONT PANEL OPERATION
    • 5.1 Introduction
      • 5.1.1 LED Indicators
      • 5.1.2 Keypad
      • 5.1.3 Vacuum Fluorescent Display (VFD)
    • 5.2 CDM-570/570L Front Panel Menus
      • 5.2.1 Opening Screen
      • 5.2.2 SELECT: (Main) Menu
        • 5.2.2.1 (SELECT:) Config (Configuration) Menus
          • 5.2.2.1.1 CONFIG: Rem (Remote Control)
            • 5.2.2.1.1.1 (CONFIG: Remote Control) Serial
            • 5.2.2.1.1.2 (CONFIG:) Remote Control: Ethernet
          • 5.2.2.1.2 CONFIG: All
          • 5.2.2.1.3 CONFIG: Tx (Transmit)
            • 5.2.2.1.3.1 (CONFIG: Tx) FEC (FEC Type)
            • 5.2.2.1.3.2 (CONFIG: Tx) Mod (Modulation)
            • 5.2.2.1.3.3 (CONFIG: Tx) Code (Code Rate)
            • 5.2.2.1.3.4 (CONFIG: Tx) Data (Data Rate)
            • 5.2.2.1.3.5 (CONFIG: Tx) Frq (Frequency)
            • 5.2.2.1.3.6 (CONFIG: Tx) On/Off
            • 5.2.2.1.3.7 (CONFIG: Tx) Pwr (Power)
            • 5.2.2.1.3.8 (CONFIG: Tx) Scram (Scrambling)
            • 5.2.2.1.3.9 (CONFIG: Tx) Clk (Clock Source)
            • 5.2.2.1.3.10 (CONFIG: Tx) Inv (Inversion Functions)
          • 5.2.2.1.4 CONFIG: Rx (Receive)
            • 5.2.2.1.4.1 (CONFIG: Rx) FEC (FEC Type)
            • 5.2.2.1.4.2 (CONFIG: Rx) Dem (Demodulation)
            • 5.2.2.1.4.3 (CONFIG: Rx) Code (Code Rate)
            • 5.2.2.1.4.4 (CONFIG: Rx) Data (Data Rate)
            • 5.2.2.1.4.5 (CONFIG: Rx) Frq (Frequency)
            • 5.2.2.1.4.6 (CONFIG: Rx) Acq (Acquisition Range)
            • 5.2.2.1.4.7 (CONFIG: Rx) Descram (Descrambling)
            • 5.2.2.1.4.8 (CONFIG: Rx) Buf (Buffer)
            • 5.2.2.1.4.9 (CONFIG: Rx) Inv (Inversion Functions)
            • 5.2.2.1.4.10 (CONFIG: Rx) Eb/N0
          • 5.2.2.1.5 CONFIG: CEx (G.703 Clock Extension)
          • 5.2.2.1.6 CONFIG: Frame (Framing Mode)
            • 5.2.2.1.6.1 (CONFIG: Framing Mode) EDMAC or EDMAC-2
          • 5.2.2.1.7 CONFIG: Intfc (Interface)
            • 5.2.2.1.7.1 (CONFIG: Interface) RS422 or V.35 or RS232
            • 5.2.2.1.7.2 (CONFIG: Interface) IP
            • 5.2.2.1.7.3 (CONFIG: Interface) G.703
          • 5.2.2.1.8 CONFIG: Ref (Reference)
          • 5.2.2.1.9 CONFIG: Mask
            • 5.2.2.1.9.1 (CONFIG: Alarm Mask) Transmit
            • 5.2.2.1.9.2 (CONFIG: Alarm Mask) Receive
            • 5.2.2.1.9.3 (CONFIG: Alarm Mask) Ref
            • 5.2.2.1.9.4 (CONFIG: Alarm Mask) BUC (CDM-570L ONLY)
            • 5.2.2.1.9.5 (CONFIG: Alarm Mask) LNB (CDM-570L ONLY)
          • 5.2.2.1.10 CONFIG: ODU (CDM-570L ONLY)
        • 5.2.2.2 SELECT: Monitor
          • 5.2.2.2.1 MONITOR: Alarms
            • 5.2.2.2.1.1 (MONITOR: Live Alarms) Unit
            • 5.2.2.2.1.2 (MONITOR: Live Alarms) Receive (Receive Traffic Status)
            • 5.2.2.2.1.3 (MONITOR: Live Alarms) Transmit (Transmit Traffic Status)
          • 5.2.2.2.2 MONITOR: Rx-Params
          • 5.2.2.2.3 MONITOR: Event-Log (Stored Events)
            • 5.2.2.2.3.1 (MONITOR: Stored Events) View
            • 5.2.2.2.3.2 (MONITOR: Stored Events) Clear-All
          • 5.2.2.2.4 MONITOR: Stats (Link Statistics)
            • 5.2.2.2.4.1 (MONITOR: Link Statistics) View
            • 5.2.2.2.4.2 (MONITOR: Link Statistics) Clear-All
            • 5.2.2.2.4.3 (MONITOR: Link Statistics) Config (Configure)
          • 5.2.2.2.5 MONITOR: AUPC
          • 5.2.2.2.6 MONITOR: ODU (CDM-570L ONLY)
        • 5.2.2.3 SELECT: TEST
        • 5.2.2.4 SELECT: Info
          • 5.2.2.4.1 INFO: All
          • 5.2.2.4.2 INFO: Tx (Transmit)
          • 5.2.2.4.3 INFO: Rx (Receive)
          • 5.2.2.4.4 INFO: Buf (Buffer)
          • 5.2.2.4.5 INFO: Frame (Framing and EDMAC)
          • 5.2.2.4.6 INFO: Intfc (Interface)
          • 5.2.2.4.7 INFO: Rem (Remote Control)
          • 5.2.2.4.8 INFO: Msk (Alarm Mask)
          • 5.2.2.4.9 INFO: Ref (Frequency Reference)
          • 5.2.2.4.10 INFO: ID (Circuit ID)
          • 5.2.2.4.11 INFO: 1:1 (1:1 Redundancy)
        • 5.2.2.5 SELECT: Save/Load
          • 5.2.2.5.1 Save/Load Configuration: Save
          • 5.2.2.5.2 Save/Load Configuration: Load
        • 5.2.2.6 SELECT: Utility
          • 5.2.2.6.1 UTIL: Buffer (Buffer Re-center)
          • 5.2.2.6.2 UTIL: Clock (Set Real-time Clock)
          • 5.2.2.6.3 UTIL: Ref (Reference)
          • 5.2.2.6.4 UTIL: Ref ( Adjust
          • 5.2.2.6.5 UTIL: Ref ( Warm-up Delay
          • 5.2.2.6.6 UTIL: ID (Circuit ID)
          • 5.2.2.6.7 UTIL: 1:1 (Manual 1:1 Switchover)
          • 5.2.2.6.8 UTIL: VFD (Video Fluorescent Display Brightness)
          • 5.2.2.6.9 UTIL: Firmware
            • 5.2.2.6.9.1 (UTIL: Firmware Image) Info
            • 5.2.2.6.9.2 (UTIL: Firmware Image) Select
          • 5.2.2.6.10 UTIL: FAST (FAST Code Options)
            • 5.2.2.6.10.1 (UTIL: FAST) Cnfg (FAST Configuration)
            • 5.2.2.6.10.2 (UTIL: FAST) View
        • 5.2.2.7 SELECT: ODU Menus (CDM-570 ONLY)
  • Chapter 6. ETHERNET-BASED REMOTE PRODUCT MANAGEMENT
    • 6.1 Introduction
    • 6.2 Ethernet Management Interface Protocols
    • 6.3 HTTP (Web Server) Interface
      • 6.3.1 HTTP Interface – Typical Operational Features
        • 6.3.1.1 Interface Access
        • 6.3.1.2 Navigation
        • 6.3.1.3 Page Sections
        • 6.3.1.4 Execution Buttons
        • 6.3.1.5 Feature Selection
        • 6.3.1.6 Text or Data Entry
    • 6.4 SNMP Interface
      • 6.4.1 Management Information Base (MIB) Files
      • 6.4.2 SNMP Community Strings
      • 6.4.3 SNMP Traps
      • 6.4.4 MIB-II
      • 6.4.5 Private MIB
    • 6.5 Telnet Interface
      • 6.5.1 Telnet Operation via HyperTerminal
  • Chapter 7. BASE MODEM HTTP INTERFACE
    • 7.1 Overview
    • 7.2 Base Modem HTTP Interface Introduction
      • 7.2.1 Interface Access
      • 7.2.2 CDM-570 Menu Tree and Splash Page
      • 7.2.3 CDM-570L Menu Tree and Splash Page
    • 7.3 HTTP Interface Page Descriptions
      • 7.3.1 Home Pages
        • 7.3.1.1 Home | Home
        • 7.3.1.2 Home | Contact
        • 7.3.1.3 Home | Support
      • 7.3.2 Admin Pages
        • 7.3.2.1 Admin | Access
        • 7.3.2.2 Admin | Remote
      • 7.3.3 Config Mdm (Configure Modem) Pages
        • Config Mdm | Modem
        • 7.3.3.2 Config Mdm | Modem Utilities
        • 7.3.3.3 Config Mdm | AUPC
      • 7.3.4 Stats Pages
        • 7.3.4.1 Stats | Modem Status
        • 7.3.4.2 Stats | Modem Logs
      • 7.3.5 ODU (Outdoor Unit) Pages
      • 7.3.6 Maint (Maintenance) | Unit Info Page
  • Chapter 8. FEC (FORWARD ERROR CONTROL)
    • 8.1 Introduction
    • 8.2 Viterbi
    • 8.3 Reed-Solomon Outer Codec (Hardware Option)
    • 8.4 Trellis Coding (requires 8-PSK/8-QAM FAST Option)
    • 8.5 Turbo Product Codec (Hardware Option)
      • 8.5.1 Introduction
      • 8.5.2 TPC modes available in the CDM-570/570L
      • 8.5.3 8-QAM Modulation
      • 8.5.4 End-to-End Processing Delay
      • 8.5.5 Comparison of all TPC Modes
    • 8.6 Uncoded Operation (No FEC)
    • 8.7 Rates above 2.5 Msymbols/sec
  • Chapter 9. AUTOMATIC UPLINK POWER CONTROL (AUPC)
    • 9.1 Introduction
    • 9.2 Setting AUPC Parameters
      • 9.2.1 Target Eb/N0
      • 9.2.2 Max Range
      • 9.2.3 Alarm
      • 9.2.4 Demod Unlock
    • 9.3 Compensation Rate
    • 9.4 Monitoring
  • Chapter 10. CLOCKING MODES
    • 10.1 Introduction
    • 10.2 Transmit Clocking
      • 10.2.1 Internal Clock
      • 10.2.2 Tx Terrestrial
      • 10.2.3 Rx Loop-Timed, Rx=Tx
      • 10.2.4 Rx Loop-Timed, Rx<>Tx (Asymmetric Loop Timing)
    • 10.3 Receive Clocking
      • 10.3.1 Buffer Disabled (Rx Satellite)
      • 10.3.2 Buffer Enabled, Tx=Rx
      • 10.3.3 Buffer Enabled, Rx<>Tx
    • 10.4 X.21 Notes
    • 10.5 G.703 Clock Extension
      • 10.5.1 Clock Extension Mode 1
      • 10.5.2 Clock Extension Mode 2
      • 10.5.3 Clock Extension Mode 3
  • Chapter 11. EDMAC CHANNEL
    • 11.1 Theory of Operation
    • 11.2 M&C Connection
    • 11.3 Setup Summary
  • Chapter 12. OFFSET QPSK OPERATION
  • Chapter 13. ETHERNET IP MODULE INTERFACE
    • 13.1 Introduction
    • 13.2 Major Assemblies
    • 13.3 Ethernet IP Module Standard Features
      • 13.3.1 10/100BaseT Ethernet Interface
      • 13.3.2 Network-Based Management
      • 13.3.3 Remote Software/Firmware Upgrade via FTP
      • 13.3.4 Configuration Backup and Restore via FTP
      • 13.3.5 Event Logging to Capture all IP Module Activity
      • 13.3.6 Detailed Statistics of IP Traffic
      • 13.3.7 IGMP Support for Multicast
      • 13.3.8 Static IP Routing for Unicast and Multicast
      • 13.3.9 Managed Switch Mode
        • 13.3.9.1 Managed Switch Mode Operation
      • 13.3.10 Streamline Encapsulation
        • 13.3.10.1 Combined Working Mode
    • 13.4 IP Module Optional Features
      • 13.4.1 CDM-570/570L IP Module Demo Mode
      • 13.4.2 3xDES Encryption with Ability to Change Keys
      • 13.4.3 IP Header Compression
      • 13.4.4 Payload Compression
        • 13.4.4.1 ADLC vs. LZS Compression Comparison
      • 13.4.5 Quality of Service
        • 13.4.5.1 Maximum Bandwidth/Priority QoS Mode
        • 13.4.5.2 Minimum/Maximum Bandwidth QoS Mode
        • 13.4.5.3 DiffServ QoS Mode
    • 13.5 IP Module Specifications – Supported RFCs and Protocols
    • 13.6 IP Module HTTP Interface
      • 13.6.1 Interface Access
        • 13.6.1.1 IP Module HTTP Interface “Splash” Page
        • 13.6.1.2 IP Module HTTP Interface Menu Tree
      • 13.6.2 HTTP Interface Page Descriptions
        • 13.6.2.1 Home Pages
          • Home | Home
          • 13.6.2.1.2 Home | Contact
          • 13.6.2.1.3 Home | Support
          • 13.6.2.1.4 Home | Log Off
        • 13.6.2.2 Admin Pages
          • 13.6.2.2.1 Admin | Summary
          • 13.6.2.2.2 Admin | Mode
          • 13.6.2.2.3 Admin | Access
          • 13.6.2.2.4 Admin | Features
          • 13.6.2.2.5 Admin | Remote
          • 13.6.2.2.6 Admin | Encryption
        • 13.6.2.3 Modem Pages
          • 13.6.2.3.1 Modem | Modem
          • 13.6.2.3.2 Modem | Utilities
          • 13.6.2.3.3 Modem | Status
          • 13.6.2.3.4 Modem | Logs
        • 13.6.2.4 IP Pages
          • IP | Interface
          • 13.6.2.4.2 IP | Routes
          • 13.6.2.4.3 IP | Multicast
          • 13.6.2.4.4 IP | QoS Mode
          • 13.6.2.4.5 IP | QoS (Quality of Service) Page
            • 13.6.2.4.5.1 IP | QoS (Maximum Bandwidth/Priority Mode)
            • 13.6.2.4.5.2 IP | QoS (Minimum/Maximum Bandwidth Mode)
            • 13.6.2.4.5.3 IP | QoS (DiffServ Mode)
            • 13.6.2.4.5.4 IP | QoS (VLAN – Priority/Maximum Bandwidth Mode)
          • 13.6.2.4.6 IP | ARP
          • 13.6.2.4.7 IP | VLAN
          • 13.6.2.4.8 IP | IGMP
          • 13.6.2.4.9 IP | Redundancy
        • 13.6.2.5 Stats (Statistics) Pages
          • 13.6.2.5.1 Stats | Ethernet
          • 13.6.2.5.2 Stats | Routes
          • 13.6.2.5.3 Stats | QoS
          • 13.6.2.5.4 Stats | WAN
          • 13.6.2.5.5 Stats | Compression
        • 13.6.2.6 Maint (Maintenance) Pages
          • 13.6.2.6.1 Maint | Unit Info
          • 13.6.2.6.2 Maint | Operations
          • 13.6.2.6.3 Maint | Save
          • 13.6.2.6.4 Maint | Reboot
  • Chapter 14. ETHERNET IP MODULE – CLI and TELNET OPERATION
    • 14.1 Overview
      • 14.1.1 Interface Access
    • 14.2 CLI Menu Pages
      • 14.2.1 Main Menu Page
      • 14.2.2 Administration Page
        • 14.2.2.1 Name/Password Configuration Page
        • 14.2.2.2 Access Lists Page
        • 14.2.2.3 Feature Configuration Page
        • 14.2.2.4 3xDES Encrypt/Decrypt Configuration Page
        • 14.2.2.5 SMTP Configuration Page
        • 14.2.2.6 SNMP Configuration Page
        • 14.2.2.7 Working Mode
        • 14.2.2.8 Managed Switch Multicast Option
        • 14.2.2.9 Header/Payload Compression Refresh Rate
        • 14.2.2.10 Payload Compression Refresh Rate
        • 14.2.2.11 Telnet Timeout
      • 14.2.3 Interface Configuration Page
        • 14.2.3.1 Ethernet Interface Page
          • 14.2.3.1.1 VLAN Table
        • 14.2.3.2 Satellite/HDLC Interface Page
        • 14.2.3.3 Receive HDLC Channel Addresses Page
      • 14.2.4 QoS (Quality of Service) Configuration Page
        • 14.2.4.1 QoS Rules Configuration Page – Max/Priority Mode
        • 14.2.4.2 QoS Rules Configuration Page – Min/Max Mode
        • 14.2.4.3 DiffServ Rules Configuration Page
      • 14.2.5 Route Table Configuration Page
      • 14.2.6 Protocol Configuration Page
        • 14.2.6.1 IGMP Information Page
        • 14.2.6.2 ARP Table Utilities Page
        • 14.2.6.3 Brouter Configuration Page
      • 14.2.7 Vipersat Configuration Page
      • 14.2.8 Satellite Modem Page
      • 14.2.9 Configuration Page
        • 14.2.9.1 Tx Configuration Page
        • 14.2.9.2 Rx Configuration Page
        • 14.2.9.3 Framing Mode Configuration
        • 14.2.9.4 Data Interface Configuration
        • 14.2.9.5 Reference Configuration Page
        • 14.2.9.6 Alarm Mask Configuration
        • 14.2.9.7 Block Up Converter (BUC) Configuration
        • 14.2.9.8 Low Noise Block Converter (LNB) Configuration
      • 14.2.10 1:1 Redundancy Configuration Page
      • 14.2.11 Operations and Maintenance Page
        • 14.2.11.1 Unit Information Page
        • 14.2.11.2 Statistics Page
          • 14.2.11.2.1 IP Routing Statistics Page
            • 14.2.11.2.1.1 Filter/Drop Statistics Page
          • 14.2.11.2.2 QoS Statistics Page
          • 14.2.11.2.3 Ethernet Statistics Page
          • 14.2.11.2.4 WAN Statistics
          • 14.2.11.2.5 Compression Statistics
          • 14.2.11.2.6 CPU Statistics
          • 14.2.11.2.7 VLAN Statistics
        • 14.2.11.3 Event Log Page
        • 14.2.11.4 Database Operations Page
        • 14.2.11.5 Diagnostics Page
    • 14.3 Telnet Session – Logout Option
  • Appendix A. CABLE DRAWINGS
    • A.1 Overview
      • EIA-530 to EIA-422/449 Data Cable
      • EIA-530 to V.35 DCE Conversion Cable
  • Appendix B. Eb/N0 MEASUREMENT
  • Appendix C. FAST ACTIVATION PROCEDURE
    • C.1 FAST System Overview
    • C.2 FAST Activation Procedure
      • C.2.1 Record Modem Serial Number
      • C.2.2 View Currently Installed Features
      • C.2.3 Order FAST Options
      • C.2.4 Enter FAST Access Code
      • C.2.5 Enable / Disable Demo Mode
  • Appendix D. SERIAL REMOTE CONTROL
    • D.1 Overview
    • D.2 EIA-485
    • D.3 EIA-232
    • D.4 Basic Protocol
    • D.5 Packet Structure
      • D.5.1 Start of Packet
      • D.5.2 Target Address
      • D.5.3 Address Delimiter
      • D.5.4 Instruction Code
      • D.5.5 Instruction Code Qualifier
      • D.5.6 Optional Message Arguments
      • D.5.7 End Of Packet
    • D.6 Remote Commands / Queries
      • D.6.1 Transmit (Tx) Commands and Queries
      • D.6.2 Receive (Rx) Commands and Queries
      • D.6.3 Unit Commands and Queries
      • D.6.4 Bulk Commands and Queries
      • D.6.5 BUC Commands and Queries (CDM-570L ONLY)
      • D.6.6 LNB Commands and Queries (CDM-570L ONLY)
  • Appendix E. CDM/CDD NMCS PROTOCOL – REV 1.0
    • E.1 Revision History
    • E.2 Introduction
    • E.3 Architecture
    • E.4 Command Set Introduction
      • E.4.1 Telnet Interface
      • E.4.2 Basic Protocol
      • E.4.3 Command Structure
        • E.4.3.1 Start Of Packet
        • E.4.3.2 Target Address
        • E.4.3.3 Instruction Code
        • E.4.3.4 Instruction Code Qualifier
        • E.4.3.5 Optional Message Arguments
        • E.4.3.6 Table Support Qualifier
          • E.4.3.6.1 Row Index
        • E.4.3.7 Optional Argument lists
        • E.4.3.8 End Of Packet
    • E.5 Remote Commands and Queries
      • E.5.1 IP Commands and Queries
        • E.5.1.1 Admin Commands and Queries
      • E.5.2 Interface Commands and Queries
      • E.5.3 QoS Commands and Queries
      • E.5.4 Protocol Commands and Queries
      • E.5.5 Operations and Maintenance Commands and Queries
      • E.5.6 Redundancy Queries
      • E.5.7 Routing Commands and Queries
      • E.5.8 Statistics Commands and Queries
        • E.5.8.1 WAN Stats
        • E.5.8.2 IP Statistics Commands and Queries
        • E.5.8.3 Ethernet Statistics Commands and Queries
        • E.5.8.4 Quality of Service (QoS) Statistics Commands and Queries
    • E.6 PARAM Files
  • Appendix F. IP QUICK-START GUIDE
    • F.1 Quick-Start Guide Introduction
    • F.2 Getting Started
      • F.2.1 Equipment List
      • F.2.2 Equipment Setup
      • F.2.3 Transmit and Receive IF Configuration
      • F.2.4 Serial Console Port Command Line Interface (CLI) Configuration
      • F.2.5 CLI Main Menu
      • F.2.6 Restoring Factory Default Configuration
    • F.3 Managed Switch Point-to-Point System Configuration
      • F.3.1 PC Configuration
      • F.3.2 CDM-IP Configuration – Setting IP Address(es)
    • F.4 Router Mode Point-to-Point System Configuration
      • F.4.1 PC Configuration
      • F.4.2 Setting CDM-IP Modems to Router Mode Operation
      • F.4.3 Setting IP Address(es)
      • F.4.4 Set Route Table entries
    • F.5 Troubleshooting IP Module
      • F.5.1 Managed Switch Mode Troubleshooting
      • F.5.2 Router Mode Troubleshooting
  • Appendix G. ETHERNET IP MODULE – TYPICAL OPERATIONAL SETUPS
    • G.1 Overview
    • G.2 Modem Compatibility
    • G.3 IP Module Working Modes
      • G.3.1 Working Modes – HDLC Encapsulation
      • G.3.2 Working Modes – Streamline Encapsulation
      • G.3.3 Managed Switch Mode
      • G.3.4 Router Modes
        • G.3.4.1 Router Mode – Point-to-Point
        • G.3.4.2 Router Mode – Point-to-MultiPoint
        • G.3.4.3 Router Mode (Brouter Enabled) – Point-to-MultiPoint with VLAN Matching Filters
          • G.3.4.3.1 Sample Network #1 – VLAN Filtering Disabled
          • G.3.4.3.2 Sample Network #2 – VLAN Filtering Enabled
          • G.3.4.3.3 Brouter Mode with VLAN Filtering Configuration
  • Appendix H. IP REDUNDANCY
    • H.1 Introduction
    • H.2 CRS-XXX 1:1 Redundancy Switch Functional Description
      • H.2.1 CRS-180 70/140 MHz 1:1 Redundancy Switch
      • H.2.2 CRS-170A L-Band 1:1 Redundancy Switch
    • H.3 CDM-570/570L 1:1 IP Data Switching Functional Description
    • H.4 CDM-570/570L 1:1 IP Redundancy Configuration
    • H.5 Cabling With CDM-570 IF
    • H.6 Cabling With CDM-570L
  • Appendix J. GPS MODE
    • J.1 Overview
    • J.2 Hardware Setup
    • J.3 Remote Commands
  • Appendix K. CDM-570 ODU (CSAT-5060 or KST-2000A/B) OPERATION
    • K.1 Introduction
      • K.3.1 CDM-570 Front Panel Operation – Overview
      • K.3.2 CDM-570 Front Panel Operation – ODU Menu Hierarchy
      • K.3.3 SELECT: (Main) Menu
        • K.3.3.1 (SELECT:) ODU
          • K.3.3.1.1 (SELECT:) ODU – CSAT-5060 Transceiver Operation
            • K.3.3.1.1.1 ODU (Transceiver Control): Enable
              • K.3.3.1.1.1.1 COMMON ‘ODU SELECT’ SUBMENU
                • K.3.3.1.1.1.1.1 ODU SELECT: Config
                • K.3.3.1.1.1.1.2 ODU SELECT: Info
                • K.3.3.1.1.1.1.3 ODU SELECT: Monitor
                • K.3.3.1.1.1.1.4 ODU SELECT: Alarms
          • K.3.3.1.2 (SELECT:) ODU – KST-2000A/B Transceiver Operation
            • K.3.3.1.2.1 ODU (Transceiver Control): Enable
              • K.3.3.1.2.1.1 (ODU) Enable: Config (KST Configuration)
              • K.3.3.1.2.1.2 (ODU) Enable: INFO (Information)
              • K.3.3.1.2.1.3 (ODU: Enable) Status
      • K.4.1 ODU-Accessible Base Modem HTTP Interface – Overview
        • K.4.1.1 Base Modem HTTP Interface – Home Page and Menu Tree
        • K.4.1.2 ODU (Outdoor Unit) pages
          • K.4.1.2.1 ODU | Config Pages
            • K.4.1.2.1.1 ODU | Config (CSAT-5060)
            • K.4.1.2.1.2 ODU | Config (KST-2000A/B)
          • K.4.1.2.2 ODU | Status Pages
            • K.4.1.2.2.1 ODU | Status (CSAT-5060)
            • K.4.1.2.2.2 ODU | Status (KST-2000A/B)
          • K.4.1.2.3 ODU | Utilities Pages
            • K.4.1.2.3.1 ODU | Utilities (CSAT-5060)
            • K.4.1.2.3.2 ODU | Utilities (KST-2000A/B)
  • Appendix L. CDM-570L ODU (BUC, LNB) OPERATION
    • L.1 Introduction
      • L.3.1 CDM-570L Front Panel Operation Overview
      • L.3.2 CDM-570L Front Panel Operation – ODU Menu Hierarchy
      • L.3.3 SELECT: (Main) Menu
        • L.3.3.1 (SELECT:) Config (Configuration)
          • L.3.3.1.1 CONFIG: Mask
            • L.3.3.1.1.1 (CONFIG: Mask) Alarm Mask: BUC
            • L.3.3.1.1.2 (CONFIG: Mask) Alarm Mask: LNB
          • L.3.3.1.2 CONFIG: ODU (Outdoor Unit)
            • L.3.3.1.2.1 (CONFIG: ODU (Outdoor Unit)) BUC
              • L.3.3.1.2.1.1 (CONFIG: ODU (Outdoor Unit)) BUC: M&C-FSK
              • L.3.3.1.2.1.2 (CONFIG: ODU (Outdoor Unit)) BUC: DC-Power
              • L.3.3.1.2.1.3 (CONFIG: ODU (Outdoor Unit)) BUC: 10MHz
              • L.3.3.1.2.1.4 (CONFIG: ODU (Outdoor Unit)) BUC: Alarm
              • L.3.3.1.2.1.5 (CONFIG: ODU (Outdoor Unit)) BUC: LO
              • L.3.3.1.2.1.6 (CONFIG: ODU (Outdoor Unit)) BUC: Mix
            • L.3.3.1.2.2 (CONFIG: ODU (Outdoor Unit)) LNB
              • L.3.3.1.2.2.1 (CONFIG: ODU (Outdoor Unit)) LNB: DC-Voltage
              • L.3.3.1.2.2.2 (CONFIG: ODU (Outdoor Unit)) LNB: 10MHz
              • L.3.3.1.2.2.3 (CONFIG: ODU (Outdoor Unit)) LNB: Alarm
              • L.3.3.1.2.2.4 (CONFIG: ODU (Outdoor Unit)) LNB: LO
              • L.3.3.1.2.2.5 (CONFIG: ODU (Outdoor Unit)) LNB: Mix
        • L.3.3.2 (SELECT:) Monitor
          • L.3.3.2.1 MONITOR: Alarms
            • L.3.3.2.1.1 (MONITOR: Live Alarms) ODU
          • L.3.3.2.2 MONITOR: ODU
            • L.3.3.2.2.1 (MONITOR: Outdoor Unit Monitor) BUC
            • L.3.3.2.2.2 (MONITOR: Outdoor Unit Monitor) LNB
      • L.4.1 ODU-Accessible Base Modem HTTP Interface – Overview
        • L.4.1.1 Base Modem HTTP Interface – Home Page and Menu Tree
      • L.4.2 ODU (BUC, LNB) Pages
        • L.4.2.1 Config Mdm | BUC (Block Up Converter)
        • L.4.2.2 Config Mdm | LNB (Low-Noise Block Down Converter)
      • L.5.1 ODU-Accessible IP Module HTTP Interface – Overview
        • L.5.1.1 IP Module HTTP Interface – Home Page and Menu Tree
      • L.5.2 ODU Configuration Pages
        • L.5.2.1 Modem | BUC (Block Up Converter)
        • L.5.2.2 Modem | LNB (Low-Noise Block Down Converter)
  • METRIC CONVERSIONS
• BACK COVER