Document Outline

• Table of Contents
• List of Figures
• Chapter 1 Introduction
  • 1.1 UPS Standard Features
    • Control Panel
    • Customer Interface
    • X-Slot Communication Bay
    • Mini‐CSB (Communication Server Board)
    • ConnectUPS-X Web/SNMP Card X-Slot Card
    • ABM Technology
    • Powerware LanSafe Power Management Software
    • Installation Features
  • 1.2 Options and Accessories
    • Integrated Battery Cabinets
    • Integrated Distribution Cabinet
    • Integrated Accessory Cabinet s (IAC-B, IAC-T, and IAC-D)
    • Powerware Hot Sync Parallel System
    • Sync Control
    • Optional X-Slot Cards
    • Remote Monitor Panel
    • Relay Interface Module
    • Supervisory Contact Module
  • 1.3 Basic System Configurations
  • 1.4 Conventions Used in This Manual
  • 1.5 For More Information
  • 1.6 Getting Help
• Chapter 2 Safety Warnings
• Chapter 3 UPS Installation Plan and Unpacking
  • 3.1 Creating an Installation Plan
  • 3.2 Preparing the Site
    • Environmental Considerations
    • Preparing for Wiring the UPS System
  • 3.3 Inspecting and Unpacking the UPS Cabinet
• Chapter 4 Installing the UPS System
  • 4.1 Preliminary Installation Information
  • 4.2 Unloading the Powerware 9390 UPS Cabinet from the Pallet
  • 4.3 Battery Cabinet Installation
  • 4.4 Integrated Distribution Cabinet Installation
  • 4.5 Integrated Accessory Cabinet Installation
  • 4.6 UPS Sidecar Wiring
  • 4.7 Installing UPS External and Battery Power Wiring
  • 4.8 Installing Interface Connections
    • TB1 and TB2 Connections
    • TB1 Battery Cabinet Connections
    • X-Slot Connections
  • 4.9 Installing Accessories and Parallel System Control Wiring
  • 4.10 Initial Startup
  • 4.11 Completing the Installation Checklist
• Chapter 5 Installing a Remote Emergency Power-off Control
  • 5.1 REPO Installation
• Chapter 6 Installing Optional Accessories
  • 6.1 Installing a Powerware Hot Sync® CAN Bridge Card
  • 6.2 Installing Parallel System Control Wiring
  • 6.3 Installing an RMP
  • 6.4 Installing an RIM
  • 6.5 Installing an SCM
• Section IIOperation
• Chapter 7 Understanding UPS Operation
  • 7.1 Single Module Reverse Transfer (RT)
    • Single Module RT Modes
    • Normal Mode – RT
    • Bypass Mode – RT
    • Battery Mode – RT
  • 7.2 Multiple Module Parallel System
    • Multiple Module Parallel System Modes
    • Normal Mode – Parallel
    • Bypass Mode – Parallel
    • Battery Mode – Parallel
  • 7.3 Functional Description
    • Input Rectifier
    • Inverter
    • Battery Charger and ABM
    • Bypass
    • Batteries
• Chapter 8 Using the Control Panel
  • 8.1 Using the LCD and Pushbuttons
  • 8.2 Using the Main Menu
    • Mimic Screen
    • Event Screens
    • Unit Meter Screens
    • Battery Discharge Log
    • kW Demand Log
    • Maximum Current Log
    • System Meters Screens
    • System Setup Level 0 Screens
    • System Setup Level 1 Screens
  • 8.3 System Controls Screen
  • 8.4 Load Off Screen
  • 8.5 Reading the Status Indicators
• Chapter 9 UPS Operating Instructions
  • 9.1 Single Module Operation
    • Starting the UPS in Normal Mode
    • Starting the UPS in Bypass Mode
    • Starting the Power Module
    • Transfer from Normal to Bypass Mode
    • Transfer from Bypass to Normal Mode
    • Transfer from Normal to Bypass Mode and Shut Down UPS
    • UPS and Critical Load Shutdown
    • Charger Control
    • Using the UPS LOAD OFF Pushbutton
    • Using the Remote Emergency Power-off Switch
  • 9.2 Multiple Module Parallel Operation
    • Starting the Parallel System in Normal Mode
    • Starting the Parallel System in Bypass Mode
    • Transfer Parallel System from Normal to Bypass Mode
    • Transfer Parallel System from Bypass to Normal Mode
    • Single UPM Shutdown
    • Restarting a Single UPM
    • Parallel System and Critical Load Shutdown
    • Using the UPS LOAD OFF Pushbutton
    • Using the Parallel System Remote Emergency Power-off Switch
• Chapter 10 Using Features and Options
  • 10.1 Building Alarm Monitoring
  • 10.2 General Purpose Relay Contact
  • 10.3 Remote Monitor Panel
  • 10.4 Relay Interface Module
  • 10.5 Supervisory Contact Module
• Chapter 11 Responding to System Events
  • 11.1 General
  • 11.2 System Event Horns
  • 11.3 System Event Indicators
  • 11.4 System Event Messages
• Chapter 12 Communication
  • 12.1 X-Slot Cards
  • 12.2 Powerware LanSafe Power Management Software
  • 12.3 Remote Notification
• Chapter 13 Maintaining the UPS System
  • 13.1 Important Safety Instructions
  • 13.2 Performing Preventive Maintenance
    • Daily Maintenance
    • Monthly Maintenance
    • Annual Maintenance
    • Battery Maintenance
  • 13.3 Recycling the Used Battery or UPS
  • 13.4 Maintenance Training
• Chapter 14 Product Specifications
  • 14.1 Model Numbers
  • 14.2 Single Module Specifications
    • UPS System Input
    • UPS System Output
    • Environmental
  • 14.3 Multiple Module Parallel Specifications
    • UPM Input
    • UPM Output
    • Environmental
    • Module Tie Cabinet Input
    • Module Tie Cabinet Output
• Chapter 15 Warranty
• Appendix AInstallation Information