Basler Electric BE1-BPR - Manual (Page 173)

9272000990 Rev J BE1-BPR Commands Summary B-1
APPENDIX B • COMMANDS SUMMARY
INTRODUCTION
Table B-1 provides an alphabetical list of communication commands. Refer to Figures 4-2 and 4-3 of
Section 4, Functional Description, for HMI menu branch numbering and screen locations.
Table B-1. Communication Commands
∗ = Enhanced Relays Only HMI Menu Branch
Command Function
Standard
Models
Enhanced
Models
ACCESS[=<password>] Read/change access area in order to
change settings.
N/A N/A
BKRCON[=<DMAX>,<Tc>,<Ti>] ∗ Read/change breaker contact data. 3 3
BKROPS[=<#operations>,<52a/b contact logic>] Read/change breaker operations data. 3 3
BKRRES[=<MAXOPS>,<reset>,<lres>] Read/change breaker resistor data. N/A N/A
CAL[x[=<level>]] Read/change ADC channel calibration. 5 6
COM[x[=<ratedps>[,Ay][,Ey][,Hy][,Pyy][,Xy]] Read/change the serial communications
protocol.
5 6
CT[P/N][=<ratio>] Read/change the Phase or Neutral CT ratio. N/A N/A
DATE[=<dm>/<md>/<yr>] Read/change the date. 5 6
DIAG[=0] Read/reset diagnostic log information. 2 2
DLOG[p[=<yy>]] ∗ Read/change the contact duty log. N/A 3
FLOG[x][=0]
∗ Read fault log or clear FLOG and FAULT
data.
N/A 5
FLT<#.<type> ∗ Read COMTRADE report for fault <xxx>. N/A N/A
FREQ[=<freq>] Read/change power system frequency. 5 6
HELP/H or HELP/H<cmd> or HELP1/H1 HELP/H returns information about using
HELP. HELP/H<cmd> returns help on a
specific command.
HELP1/H1 returns a complete list of
commands.
N/A N/A
I[<phase> Read phase current in primary units. 2 2
ID[=<id>] Read/change relay ID number for polled
communications.
N/A N/A
LF[x][=<type>,<dflt>] Read/change logic for fault detector
operation.
N/A N/A
LI[x][=<r>,<db>] Read/change logic for contact inputs. N/A N/A
LINFO[<name>] Read logics available or <name> logic
equations.
N/A N/A
LN[=<name>] Read/change custom logic name. 1 1
LO[#[=<Boolean equation>]] Read/change program operation for an
output.
N/A N/A
LOGIC[=<existing name>] Read/change the name of the active logic
scheme.
1 1
LR[=<type>,<start>,<reset>,<wait>,<lockout>] Read/program the logical inputs to the
recloser function block.
N/A N/A
LT[x[=<type>,<start>,<reset>]] Read/change logic for timer/counter
operation.
N/A N/A
OUT[x][=<1/0>/DISABLE] Pulse output ON (1) OR OFF (0) for test. N/A N/A
PCLK[=[<date_format>,<time_format>] Read/program date/time format. N/A N/A
PDIAG[=<DIAG1 mask>,<DIAG2 mask>] Read/program diagnostic alarms as ON (1)
or OFF (0).
N/A N/A
PDISPLAY[=<default_menu>,<default_screen>] Read/program the default display screen. N/A N/A
PHOLD[=<#####>] Read/program the 200 msec output hold
mask.
N/A N/A