Daktronics OmniSport 2000 Timing Console - Manual (Page 256)

ED13584
Rev 8 19 August 2013
Page 4 of 8 201 Daktronics Drive PO Box 5128, Brookings, SD 57006-5128
Tel: 1-800-DAKTRONICS (1-800-325-8766) Fax: 605-697-4700
Web: www.daktronics.com/support
Step 1:
Clear any old information from the Dive Orders A to D.
 Press [ SELECT ORDER ]>[ A ] to set the current Diver Order to A.
 Press [ MENU ]>[2]>[3]>[ ENTER ] to clear out Dive Order A.
 Repeat this step selecting [ B ], [ C ], [ D ] to clear the remaining Dive Orders.
Step 2: (Optional)
Enter the Dive List for each of the divers in Dive Order A.
 Press [ SELECT ORDER ]>[A] to set the current Diver Order to A.
 Verify on the left LCD that the Diver # and Round are both set to 01.
 Enter the first diver’s dive list by pressing [
MENU ]>[2]>[4]>[ ENTER ].
 The LCD will prompt you to enter the Dive and Position. Use the numeric keypad to enter the four digit dive number
and the [A], [B], [C], or [D] key to select the position. Press [
ENTER ] to accept the dive and position. Use the numeric
keypad to enter the degree of difficulty (DD) for the dive selected. Press [ ENTER ] to accept the DD and increment
the round by one. Repeat this sequence to enter the dive, position, and DD for each additional round for the
selected diver.
 After the first diver’s dive list is entered, press [] to increment the diver by one. Press [] as many times as
necessary to decrement the round to one. Now r
epeat the above instructions for each diver’s dive list.
NOTE: When in the Editing Order menu, use [] to decrement the round by one, [] to increment the round by
one, [] to decrement the diver by one, and [] to increment the diver by one.
 Press [Print]>[3]> [ ENTER ] to print the dive list for all the divers in the selected dive order.
 Repeat this step selecting [B], [C], [D] to pre-program each dive order.
Step 3:
 Press [ MENU ]>[4]>[1]>[1] and press [2], [3], [5], [7], or [9] to enter the correct number of judges. If seven or nine
judges are selected, it will prompt you for the correct formula.
Step 4:
 Press [ SELECT ORDER ] and [A], [B], [C], or [D] to select the desired dive order.
 Verify on the left LCD that the diver number and round are both set to 01.
Step 5:
 Select a diver, dive, position, and DD.
When the Dive Order is pre-programmed: (pre-programming is done in Step 2 of this list.)
 Verify on the middle LCD that the correct dive, position and DD are programmed.
 If not, press [ EDIT ] and correct any mistakes.
 Press [ SCORE ] and the left two LCDs will prompt you for the judge’s scores.
When the Dive Order is not pre-programmed:
 Press [ SCORE ] and the left two LCDs will prompt you to enter dive and position. Use the numeric keypad to enter
the three or four digit dive number and [A], [B], [C], [D] for the position. Press [ ENTER ] to accept the dive and
position. Use the numeric keypad to enter the DD for the dive selected, then press [ ENTER ]. The left two LCDs will
prompt you for the judge’s score.
 Use [0], [.5] through [10] on the insert to fill in the judge’s scores. Press [
FAIL ] or [ BALK ] if they apply.
 When the correct judge’s scores have been filled in, press [
SCORE ] to accept the award score and advance to the
next diver in that round and repeat Step 5.
 If that was the last diver for that round, press [] to increment the round by one. Next, press [ DIVER

]>[1]>[ ENTER ]
and then repeat Step 5.
Typical Diving Operation
The diving program in the OmniSport 2000 console will allow up to 25 divers for four different dive orders (labeled A, B,
C, and D). Each Dive Order can have up to 13 rounds.
You can pre-program dive sheets for each diver, or you can enter them while the event is running.
If you are using a programmed Event Order configured with Swimming and Diving event numbers, the first event that is
set to diving will be Dive Order A, the second will be Dive Order B, the third Dive Order C and the fourth will be Dive
Order D. If there are more than four Diving events, they will switch back to Dive Order A when selected.