Kenwood TS-990S - Manual (Page 136)

5-58
5 ASSISTING YOUR SMOOTH QSO
Index Contents
Each time you press [CHAR] (F), the character type cycles
through the following sequence:
ABC (upper case) > abc (lower case) > ÀÁÂ (upper case) >
àáâ (lower case) > !”# (symbols) > ABC (upper case)
■ Available alphanumeric characters and symbols (a
maximum of 70 characters)
Following are the available characters and symbols with
“English” selected in Menu 9-01. If you wish to enter the
Japanese characters, download the Japanese instruction
manual to refer to the available characters and symbols for
the Japanese characters.
A B C D E F G H I J K L M N O
P Q R S T U V W E X Y Z
0 1 2 3 4 5 6 7 8 9
a b
c d e f g h i j k l m n o
p q r s t u v w x y z
А Б В Г Д Е Ж З И Й К Л М Н О
П Р С Т У Ф Х Ц Ш Щ Ъ Ы Ь Э Ю
а б в г д е ж з и й к л м н о
п р с т у ф х ц ш щ ъ ы ь э ю
я Я
! " # $ % & ' ( ) * + , - . /
: ; < = > ? @ [ \ ] ^ _ ` { |
} ~ ¡ ¢ £ ¤ ¥ ¦ § ¨ © ª « ¬ ®
¯ ° ± ² ³ ´ µ ¶ • ¸ ¹ º » ¼ ½
¾ ¿ No ÷ Space Line Break
• Pressing [CANCEL] (F7) deletes the contents being edited
and ends the character entry.
7 Press [SAVE] (F6) to store the edited message.
8 Press [
] (F1).
9 Press [ESC] to exit.
CONFIGURING AUTOMATIC TRANSMISSION AND
RECEPTION FOR THE PSK MESSAGE MEMORY
If you select an PSK message memory channel, you
can configure independently for each message memory
channel whether or not the PSK message is transmitted
automatically and whether or not the transceiver enters
receive after it’s been sent.
Automatic Transmit sends the PSK message as soon
as the channel where a PSK message is stored is
selected. The transmit state is maintained even after the
entire message is transmitted. Therefore, this function
is convenient if you wish to transmit your own text string
using a USB keyboard after a PSK message is transmitted
using the message memory.
Automatic Receive is a function to revert to the receive
mode after an PSKY message has been sent.
Selecting the channel number, that contains a PSK
message to be sent, automatically starts transmitting the
message, or the message temporarily stored in the buffer
for the text string can be sent with a press of [F12] of a
USB keyboard. The transceiver can automatically enter
the receive mode after the PSK message is transmitted.
A combination of automatic transmission and automatic
reception makes it possible to transmit and receive
messages automatically.
[F1] [F7]
[FSK/PSK/REV] [ESC] [MULTI/CH]
1 Press [FSK/ PSK/ REV] to enter PSK mode.
2 Press [DECODER] (F3) to open the PSK Encode/
Decode screen.
3 Press [MEMORY] (F5) to open the PSK Message
screen.
If [MEMORY] (F5) is unavailable in the function key guide,
press [MORE] (F1). An alternate key guide will appear.
4 Press [ ] (F3) or [ ] (F4), or rotate the
MULTI/CH control to select a channel where a CW
message to be sent automatically is stored.
5 Press [AUTO.TX] (F6) to enable automatic
transmission.
The transceiver can be configured to allow an RTTY
message to be transmitted automatically from the
corresponding channel when "AUTO TX" appears on the
right side of the RTTY message. Even if the "AUTO TX"
disappears, the PSK message for that channel is temporarily
stored in the buffer for a text string and will not automatically
be sent.
6 Press [AUTO.RX] (F7) to enable automatic
transmission.
You can configure the transceiver so that the transceiver will
revert to a receive state after an PSK message is transmitted
from the corresponding channel when "AUTO RX" appears
on the right side of the PSK message. Even if "AUTO RX"