Menu items, Switching the operating data between config a and, Config b -2 – Kenwood TS-990S User Manual

Page 44: Menu items -2

Advertising
background image

3 MENU

3-2

Index

Contents

SWITCHING THE OPERATING DATA BETWEEN CONFIG

A AND CONFIG B

Parameters configured in the menu and various

configurations for operation are jointly called the operating

environment. The transceiver has CONFIG A and CONFIG

B as two separate environments. Both contain the same

configuration items, allowing you to configure them

individually. For example, CONFIG A might be configured

for DX hunting and CONFIG B for rag-chewing, and you

can quickly switch from one to another.
1 Press [MENU] to open the Menu screen.
2 Press [CONFIG] (F7).
3 Press [OK] (F4) to switch CONFIG A to CONFIG B.

After changing the configuration, you can immediately

operate the transceiver with the new configuration enabled.

Pressing [CANCEL] (F7) reverts to the Menu screen.

Note:

◆ The current status of the operating environment, either "CONFIG

A" or "CONFIG B", appears on the status bar of the Menu screen.

Also, the operating environment data can be stored to or read from

a USB flash drive.

{page 12-1}

◆ Following are the configurations that are common to CONFIG A

and CONFIG B.

• Baud rate for the COM port

• Baud rate for the USB port

• The number of quick memories

◆ The [MR] (Quick Memory) function

{page 10-8}

includes some

operating environment parameters. Changes made to CONFIG

A or CONFIG B here will clear the QM operating environment and

then switch to the new operating environment.

MENU ITEMS

Basic Configurations (Group 0)

Menu

Display

Configuration

Range

Default

Reference

Page

Display

0-00

Color Display Pattern (Main Screen)

The background color pattern for the

main screen

Type 1, Type 2, Type 3

Type 1

4-5

0-01

Color Display Pattern (Sub Screen)

The background color pattern for the

sub-screen

Type 1, Type 2, Type 3, Same

as Main

Same as

Main

4-5

0-02

Font Style (Frequency Display)

Font style to be applied to the

frequency display

Font 1, Font 2, Font 3

Font 1

4-5

0-03

Dial Color Pattern

The background color pattern for the

sub-screen dial

Type 1, Type 2

Type 1

4-6

0-04

Screen Saver

Pattern of the screen saver

Off, Type 1, Type 2

Off

16-1

0-05

Screen Saver Wait Time

Wait time until the screen saver

activates

Preview (5 [sec]), 5, 15, 30, 60

[min]

Preview

(5 [sec])

16-2

0-06

Screen Saver Message

A message embedded in the screen

saver

A maximum of 10

alphanumeric characters

TS-990

16-2

0-07

Power-on Message

A message appearing during power up A maximum of 15

alphanumeric characters

HELLO

16-1

Meter

0-08

FM Mode S-meter Sensitivity

S-meter sensitivity in FM mode

Low, High

High

5-29

0-09

Meter Response Speed

ANALOG METER RESPONSE SPEED 1 to 4

3

4-19

0-10

Meter Display Pattern

Display pattern for a meter

Type 1, Type 2, Type 3

Type2

4-18

Key

0-11

Meter Display Peak Hold

METER PEAK-VALUE HOLD

Off, On

On

4-19

0-12

Long Press Duration of Panel Keys

Duration for a long press of the panel

keys

200 to 2000 [ms] (in steps of

100 [ms])

500 [ms]

16-5

0-13

Touchscreen Tuning

Touchscreen Tuning function (Main

display)

Off, On

On

16-3

0-14

Operating Band (High/Low & Shift/Width

Controls)

Selection of band for the High/Low and

Shift/Width controls

Main and Sub Bands, Main

Band only

Main and

Sub Bands

16-4

0-15

PF A: Key Assignment

Assignment of the programmable

function to [PF A]

Refer to the programmable

function key list.

VOICE 2

16-6

0-16

PF B: Key Assignment

Assignment of the programmable

function to [PF B]

Refer to the programmable

function key list.

VOICE 3

16-6

0-17

VOICE (Main Band): Key Assignment

Assignment of the programmable

function to [VOICE] (M)

Refer to the programmable

function key list.

VOICE1

(Main Band)

16-6

0-18

VOICE (Sub Band): Key Assignment

Assignment of the programmable

function to [VOICE] (S)

Refer to the programmable

function key list.

VOICE1 (Sub

Band)

16-6

0-19

External PF 1: Key Assignment

Assignment of the programmable

function to [PF 1] (Keypad)

Refer to the programmable

function key list.

Message

Memory CH1

16-7

0-20

External PF 2: Key Assignment

Assignment of the programmable

function to [PF 2] (Keypad)

Refer to the programmable

function key list.

Message

Memory CH2

16-7

Advertising