Kenwood TS-990S - Manual (Page 276)

18 TROUBLESHOOTING
18-6
Index Contents
THE LIST OF WARNING MESSAGES
A warning message appears if there is any false operation or when the transceiver detects any failure or abnormality. A
problem can be cured following the description on the warning message. If reading of "Troubleshooting" is required on
the warning message or if you cannot cure the problem, refer to the List of Warning Messages and Troubleshooting.
ID Message Overview
0012 Memory available for recording is insufficient. (WR: 0012)
Appears when the remaining memory size is insufficient to store an audio
file for the voice recording.
000F This audio file cannot be reproduced. (WR: 000F)
Appears when you attempt to play the audio file that the transceiver cannot
play.
0018
The Programmable Timer is about to start recording the
received audio. (WR: 0018)
The recording cannot begin if the transceiver has been turned
OFF. Turn the transceiver OFF and connect a USB flash drive.
Appears three minutes and one minute before the timer recording begins.
Follow the instruction given on an error message.
0019 The Programmable Timer is about to turn the transceiver OFF.
(WR: 0019)
Appears three minutes and one minute before the transceiver power ( )
turns OFF by the Off Timer.
001 A The Sleep Timer is about to turn the transceiver OFF.
(WR: 001A)
Appears three minutes and one minute before the transceiver power ( )
turns OFF by the Sleep Timer.
001 B
Recording by the Programmable Timer. (WR: 001B)
To continue recording, press [ ] to turn the transceiver OFF. To
stop recording, press and hold [(BREAK)] (F).
Appears when you attempt to turn the transceiver power ( ) On with a
press of [ ] during the timer recording.
0046
Due to insufficient memory or forbidding of the data storage to
the USB flash drive, the data storing process was terminated.
(WR: 0046)
Ensure that there is sufficient memory and that data storage
has been enabled.
Appears when the remaining memory size of the USB flash drive is
insufficient or the write protected during the writing of the audio file to the
USB flash drive.
0047
High temperature has been detected in the transmitter. Refer to
"Troubleshooting" in the instruction manual. (WR: 0047)
To prevent the transmitter from being damaged, the transmit
power has been reduced to 5 W.
Appears when the transmit power is reduced to 5 W due to detection of high
temperature.
Refer to "COOLING FAN AND TEMPERATURE PROTECTION FOR FINAL
UNIT". {page 4-3}
004 B Selects the days of the week. (WR: 004B)
Appears if no day of the week is configured while the Program Timer is
being configured.
004D
A maximum of 4 hours of recording time can be configured.
(WR: 004D)
Ensure that the Power-on Time and Power-off time are
appropriate.
Appears if you attempt to configure the recording time exceeding four hours
when you configure the Program Timer.
004E
The same clock time cannot be configured for both the Power-
on Time and Power-off Time. (WR: 004E)
Ensure that the Power-on Time and Power-off time are
appropriate.
Appears if the time to turn the transceiver power ( ) On is identical to the
time to turn the transceiver power Off.
004F
Very high temperature has been detected in the transceiver.
Refer to "Troubleshooting" in the instruction manual. (ERR:
004F)
The transceiver cannot transmit until the transceiver cools
down.
Appears when high temperature is detected and the transmission is
prohibited.
Refer to "COOLING FAN AND TEMPERATURE PROTECTION FOR FINAL
UNIT". {page 4-3}
0057
Failure in formatting of a USB flash drive has been detected.
(WR: 0057)
The failure may be caused by one or more of the following:
• The write protected USB flash drive is connected to a USB
connector.
• The USB flash drive is not correctly connected to a USB
connector.
The security-protected USB flash drive is connected to a USB
connector.
Appears when formatting of USB flash drive fails.
• You attempt to format the USB flash drive while the transceiver is
distinguishing the USB flash drive (an icon blinks).
If the formatting fails, remove the USB flash drive following the procedure
of "Safe Removal of USB Flash Drive", and then format the USB flash drive
following the procedure of "USB Flash Drive Formatting".