Kenwood TS-990S - Manual (Page 85)

5-7
ASSISTING YOUR SMOOTH QSO 5
Index Contents
4 Press [ ] (F3) [ ] (F4) and select the target
frequency to be adjusted.
5 Press [-] (F5) or [+] (F6), or rotate the MULTI/CH
control to adjust the frequency level.
6 Press [ESC] to exit.
Pressing [ ] (F1) closes the individual RX Equalizer
Adjustment screen and reverts to the RX Equalizer screen.
■ DEFAULT RX DSP EQUALIZER LEVELS [DB]
Frequency
[Hz]
HB1 HB2 FP BB1 BB2 FLAT U1 U2 U3
0 -5 +1 +3 +6 +6 0 0 0 0
300 -4 +1 +3 +2 +4 0 0 0 0
600 -5 +1 +3 -8 -1 0 0 0 0
900 -3 +1 +2 -11 -11 0 0 0 0
1200 +2 +3 -20 -11 -18 0 0 0 0
1500 +5 +5 -24 -12 -18 0 0 0 0
1800 +6 +6 -4 -11 -16 0 0 0 0
2100 +6 +6 +3 -11 -12 0 0 0 0
2400 +6 +6 +3 -11 -8 0 0 0 0
2700 +6 +6 +3 -11 -6 0 0 0 0
3000 +6 +6 +3 -12 -6 0 0 0 0
3300 +6 +6 +3 -11 -6 0 0 0 0
3600 +6 +6 +3 -11 -8 0 0 0 0
3900 +6 +6 +3 -11 -12 0 0 0 0
4200 +6 +6 +3 -11 -16 0 0 0 0
4500 +4 +6 +3 -12 -18 0 0 0 0
4800 -5 +6 -5 -11 -18 0 0 0 0
5100 -24 +6 -24 -11 -17 0 0 0 0
Note:
◆ Each default equalizer characteristics other than User 1 to User
3 can also be changed in the RX Equalizer Adjustment screen.
Press and hold [(RESET)] (F2) on the RX Equalizer Adjustment
screen to reset the equalizer characteristics to the defaults.
◆ If the configured levels for one frequency range of the receive
DSP equalizer is widely different from the configured levels for
the adjacent frequency ranges, the received audio may not be
attenuated as configured.
COPYING CUSTOMIZED EQUALIZER DATA
You can edit the predetermined equalizer characteristics
and copy the equalizer data to User 1 to User 3.
[F1] [F7] [RXEQ/SEL] [USB]
1 Press and hold [RXEQ/SEL].
The RX Equalizer screen appears.
2 Press [ ] (F2) or [ ] (F3) to select the
equalizer to be stored.
Pressing [ADJ.] (F4) on the RX Equalizer screen opens the
RX Equalizer Adjustment screen. The equalizer data can
be copied from either of the RX Equalizer and RX Equalizer
Adjustment screens.
3 In the RX Equalizer screen, press [COPY] (F5) or in
the RX Equalizer Adjustment screen, press [COPY]
(F7).
A message prompting you to specify the destination to store
the Equalizer Characteristics appears.
4 Press [USER1] (F2), [USER2] (F3), [USER3] (F4) to
specify the destination of the copy.
• Copy the equalizer data selected in step 1 to User 1, User
2, or User 3.
• After the copy has completed, the message prompting
you to specify the destination to copy the Equalizer
Characteristics disappears, and the RX Equalizer or RX
Equalizer Adjustment screen reappears.
• Pressing [CANCEL] (F7) terminates the copy of the
equalizer data (without copy) and reverts to the RX
Equalizer or RX Equalizer Adjustment screen.