Kenwood TS-990S - Manual (Page 240)

16 USEFUL FUNCTIONS
16-8
Index Contents
List of Functions for Key Assignment
Parameter Operation and activation of function assigned
MENU 0-00 to
MENU 9-03
Press to access a menu ranging from 0-00 to 9-03.
For details, refer to "Menu". {page 3-2}
AT/AT TUNE
Press to tune the signal using and via the internal
antenna tuner or leave the signal not tuned by
bypassing (through) the internal antenna tuner.
Press and hold to begin tuning the internal antenna
tuner.
VOX/SEL
Press to toggle the VOX function between active and
inactive.
Press and hold to open the VOX Level screen.
PROC/SEL
Press to toggle the Speech Processor between
active and inactive.
Press and hold to open the Speech Processor
screen.
ANT1 Press to select ANT 1.
ANT2 Press to select ANT 2.
ANT3 Press to select ANT 3.
ANT4 Press to select ANT 4.
DATA 1/SEL
Press this key to select Data 1.
Press and hold to open the Modulation Source
screen.
DATA 2/SEL
Press this key to select Data 2.
Pressing and holding this key opens the Modulation
Source screen.
DATA 3/SEL
Press this key to select Data 3.
Pressing and holding this key opens the Modulation
Source screen.
RX (Main Band)
Press to place the transceiver, with the dual band
in the receive state, in the receive state using the
single band.
TX (Main Band)
Press to allow the transceiver to transmit using the
main band frequency (Simplex).
M>S
Press to copy the operating data such as the
main band frequency and operating mode to the
operating data for the sub band.
M/S
Press to toggle the reception capability for the sub
band between active and inactive.
RX (Sub Band)
Press to toggle the dual-band watch (reception)
between ON and OFF.
TX (Sub Band)/
(Split Frequency)
Press to configure the transmit functions to the sub
band frequency and place the transceiver in the split
mode.
Press and hold to enable the configuration for split
frequency.
This is the default for Menu 28, "Microphone PF 1:
Key Assignment".
TF-SET
While [TF-SET] is pressed down, the transceiver
receives on the transmit frequency.
MAIN
Press to select the main band.
This is the default for Menu 27, "Microphone PF 2:
Key Assignment".
SUB
Press to select the sub band.
This is the default for Menu 29, "Microphone PF 3:
Key Assignment".
M/V (Memory)
Each time you press this key, the operating mode
toggles between Memory Channel mode and VFO
mode.
M.IN (Memory)
Press to toggle the memory scroll mode between
active and inactive.
M>V (Memory)
The operating data configured for the Memory
Channel will be copied to the VFO.
This is the default for Menu 30, "Microphone PF 4:
Key Assignment".
REC (Recorder)/
Full-time REC
Each time you press this key, normal recording
starts.
Press and hold to start constant recording.
STOP (Recorder) Press to stop recording or playback.
PLAY (Recorder)
Press to play back the latest audio file recorded in
normal or constant recording mode. Press this key
during playback to pause.
Parameter Operation and activation of function assigned
S.DISP/SEL
Each time you press this key, the display contents
for the sub-screen changes.
Each time you press and hold this key, the
highlighted display toggles between active and
inactive.
MR/SEL (Quick
Memory)
Each time you press this key, the Quick Memory
mode toggles between active and inactive.
Press and hold to clear all the operating data stored
in Quick Memory Channels.
M.IN (Quick
Memory)
Press to save data in Quick Memory Channels.
CW T. (Main
Band)
Press to activate CW auto tuning for the main band.
FIL A/SEL (Main
Band)
Press to select the RX Filter A for the main band.
Press and hold to open the Receive Filter screen.
FIL B/SEL (Main
Band)
Press to select the RX Filter B for the main band.
Press and hold to open the Receive Filter screen.
FIL C/SEL (Main
Band)
Press to select the RX Filter C for the main band.
Press and hold to open the Receive Filter screen.
AGC SEL (Main
Band)
Press to open the AGC screen for the main band.
The transceiver does not behave even if you press
and hold this PF key.
AGC SLOW (Main
Band)
Press to select "Slow" for the Automatic Gain
Control speed for the main band.
AGC MID (Main
Band)
Press to select "Medium" for the Automatic Gain
Control speed for the main band.
AGC FAST (Main
Band)
Press to select "Fast" for the Automatic Gain Control
speed for the main band.
AGC OFF (Main
Band)
Press to disable the Automatic Gain Control for the
main band.
NCH SEL (Main
Band)
Press to select either narrow or wide for the notch
filter bandwidth. The transceiver does not behave
even if you press and hold this PF key.
A.NCH SEL (Main
Band)
Press to open the Auto Notch Filter screen. The
transceiver does not behave even if you press and
hold this PF key.
BEF SEL (Main
Band)
Press to open the Band Elimination Filter screen
for the main band. The transceiver does not behave
even if you press and hold this PF key.
APF SEL (Main
Band)
Press to open the Audio Peak Filter screen for the
main band. The transceiver does not behave even if
you press and hold this PF key.
MUTE (Main
Band)
Press to mute the audio for the main band.
CW T. (Sub Band) Press to start CW auto tuning for the sub band.
FIL A/SEL (Sub
Band)
Press to select the RX Filter A for the sub band.
Press and hold to open the Receive Filter screen.
FIL B/SEL (Sub
Band)
Press to select the RX Filter B for the sub band.
Press and hold to open the Receive Filter screen.
FIL C/SEL (Sub
Band)
Press to select the RX Filter C for the sub band.
Press and hold to open the Receive Filter screen.
AGC/SEL (Sub
Band)
Press to open the AGC screen for the sub band. The
transceiver does not behave even if you press and
hold this PF key.
AGC SLOW (Sub
Band)
Press to select "Slow" for the Automatic Gain
Control speed for the sub band.
AGC MID (Sub
Band)
Press to select "Medium" for the Automatic Gain
Control speed for the sub band.
AGC FAST (Sub
Band)
Press to select "Fast" for the Automatic Gain Control
speed for the sub band.
AGC OFF (Sub
Band)
Press to disable the Automatic Gain Control for the
sub band.
NCH SEL (Sub
Band)
Press to select either narrow or wide for the notch
filter bandwidth for the sub band. The transceiver
does not behave even if you press and hold this PF
key.
A.NCH/SEL (Sub
Band)
Press to open the Auto Notch Filter screen. The
transceiver does not behave even if you press and
hold this PF key.
BEF SEL (Sub
Band)
Press to open the Band Elimination Filter screen
for the sub band. The transceiver does not behave
even if you press and hold this PF key.