Kenwood TS-990S - Manual (Page 52)

3 MENU
3-10
Index Contents
ADVANCED MENU ITEMS
Menu Display Configuration Range Default
Reference
Page
0 Indication Signal Type (Main Band)
Output signal type (main band) to an
external meter
Automatic, TX Power, ALC, Drain
Voltage (Vd), Compression Level
(COMP), Current (Id), SWR
Automatic 16-15
1 Indication Signal Type (Sub Band)
Output signal type (sub band) to an
external meter
TX Power, ALC, Drain Voltage
(Vd), Compression Level (COMP),
Current (Id), SWR
ALC 16-16
2 Output Level (Main Band)
Output signal level (main band) to an
external meter
0 to 100 [%] (in steps of 1) 50 [%] 16-16
3 Output Level (Sub Band)
Output signal level (sub band) to an
external meter
0 to 100 [%] (in steps of 1) 50 [%] 16-16
4 REF I/O Connector Configuration Configurations for the REF I/O connector Off, Output, Input Off 16-22
5 Reference Oscillator Calibration
Frequency calibration for the reference
oscillator
-255 to +255 (in steps of 1) 0 18-1
6 Bandwidth (Additional Roofing Filter)
Passband width of the additional roofing
filter
Off, 300 to 3500 [Hz] (in steps of
100 [Hz])
Off 16-22
7 Attenuation (Additional Roofing Filter) Attenuation of the additional roofing filter -20 to 0 to +20 (in steps of 1) 0 16-23
8 TX Power Down with Transverter Enabled Transmit power reduction while the
transverter is enabled
Off, On On 16-33
9 TX Hold After Antenna Tuning
Transmit hold time after completing the
antenna tuning
Off, On Off 4-23
10 Antenna Tuner during RX Antenna tuner behavior while receiving Off, On Off 4-22
11 Linear Amplifier Control (HF Band)
Linear Amplifier Control for use in the HF
band
Off, Active High, Active High +
Relay Control, Active High + Relay
& TX Delay Ctrl, Active Low, Active
Low + TX Delay Control
Off 16-31
12 Linear Amplifier Control (50 MHz Band) Linear Amplifier Control for use in the 50
MHz band
Off, Active High, Active High +
Relay Control, Active High + Relay
& TX Delay Ctrl, Active Low, Active
Low + TX Delay Control
Off 16-32
13 Microphone Gain (FM Mode) Microphone gain in FM mode 1 to 100 (in steps of 1) 50 5-28
14 PKS Polarity Reverse Reversion of the PKS polarity Off, On Off 16-29
15 TX Inhibit While Busy Transmit inhibit while in the busy state Off, On Off 16-28
16
CTCSS Unmute for Internal Speaker
(Main Band)
Muting the CTCSS tone (Main band) Mute, Unmute Mute 16-23
17
CTCSS Unmute for Internal Speaker
(Sub Band)
Muting the CTCSS tone (Sub band) Mute, Unmute Mute 16-23
18 MSQ Logic State Selecting the MSQ Logic Low, Open Low 16-24
19 SSQ Logic State Selecting the SSQ Logic Low, Open Low 16-24
20 MSQ Reverse Condition
Reversing conditions of the MSQ logic
state
Off, Busy, Sql, Send, Busy-Send,
Sql-Send
Sql 16-24
21 SSQ Reverse Condition
Reversing conditions of the SSQ logic
state
Off, Busy, Sql, Send, Busy-Send,
Sql-Send
Sql 16-24
22 Standby State Low Power Consumption Standby Power Saving Off, On
Off
(K-Type)
On
(E-type)
4-2
23 Cooling Fan Control after Shutdown Cooling fan behavior after shutdown Off, On Off 4-2
24
MSQ/ PKS Pin Assignment
(COM Connector)
Pin assignment of MSQ/PKS to the COM
connector
Off, On Off 16-25
25 External Display Output to the external display Off, On On 16-18
26 Resolution (External Display) Video Signal Resolution 800x600, 848x480 800x600 16-18
27 Touchscreen Calibration Touchscreen calibration - - 16-3
28 Software License Agreement Software License Agreement - - IV
29
Important Notices concerning Free Open
Source
Method to obtain the open source
software used in this transceiver
- - IV
30
About Various Software License
Agreements
Licensing of the software used in this
transceiver, under the GPL/LGPL
- - IV