Kenwood TS-990S - Manual (Page 58)

4 BASIC OPERATIONS
4-4
Index Contents
■ Function Keys on the right side of the Main Screen
• [ANT] (F) {page 4-20}
Press to switch the antenna configuration.
Press and hold to open the Antenna Name screen.
• [ATT] (F)
{page 6-1}
Each time you press the key, the attenuation level of
the selected band switches. Press and hold to change
the attenuation level for the selected band, in reversed
sequence.
• [P.SEL] (F) {page 6-1}
Press to toggle the Preselector between active and
inactive.
Press and hold while Preselector is enabled to open
the Preselector screen. (Main Band only)
• [P.AMP] (F) {page 5-9}
Press to toggle the Preamplifier for the selected band
between active and inactive.
• [MAX-Po] (F) {page 4-18}
Press to cycle the maximum transmit power through
On > Off > maximum transmit power value [W].
• [METER] (F) {page 4-19}
Press to cycle the transmit meter through the active
meters: Po > SWR > Id > COMP > ALC > Vd (analog
meter) SWR > Id > COMP > Vd > TEMP (digital
meters) Po > SWR > Id > COMP > ALC > Vd > TEMP
(reduced digital meter)
• [TX-FIL] (F) {page 9-8}
Press to cycle the transmit filter through FIL-A > FIL-B
> FIL-C filters. Press and hold to open the TX Filter
screen.
Note:
◆ The function names guided on the main screen vary depending on
the functions and configurations.
◆ Some function keys along the bottom of the main screen do not
appear, depending on the functions and configurations.
◆ Frames and letters for the function keys along the right side of the
main screen turn to yellow when the available band is switched to
the sub band. Functions that cannot be used for the sub band do
not appear.
SUB SCREEN
On the sub screen, pressing [S.DISP/SEL] changes
various displays, such as the standard mode display and
the enhanced display.
[MENU]
[S.DISP/SEL]
■ Switching to the Standard Mode and to the
Enhanced Mode
1 Press and hold [S.DISP/SEL] to switch to the standard
or enhanced mode.
A long press displays or hides a dial on the sub-display.
■ Changing the Display in each mode
1 Press and hold [S.DISP/SEL] to change the display.
In Normal Operation
In the standard mode display:
Each key press cycles the display through the following
sequence.
Selected Band Frequency <-> Main band and sub band
frequencies
In the enhanced mode display:
Each key press cycles the display through the following
sequence.
Selected Band Frequency <-> Main Band and sub band
frequencies
While the Encode/ Decode Screen appears:
Each key press cycles the display through the following
sequence.
The selected band frequency > Main band and sub band
frequencies > Band frequency to decode, X-Y scope (FSK
mode only), or Band frequencies to decode (PSK mode only)
> The selected band frequency
●
●
Normal Operation
While the Encode/Decode Screen Opens
Standard Screen Extended Screen
Sub-scope
Operating Band Frequency
Dial
Press and hold
[S.DISP].
Press and hold
[S.DISP].
Press and hold
[S.DISP].
Press and hold
[S.DISP].
Press [S.DISP] Press [S.DISP]
Press [S.DISP] Press [S.DISP]
Press
[S.DISP]
Press
[S.DISP]
Press [S.DISP] Press [S.DISP]
Operating Band Frequency
Vector Scope (PSK mode)
X-Y Scope (FSK mode)
Operating Band Frequency
Vector Scope (PSK mode)
X-Y Scope (FSK mode)
Main Band Frequency
Sub Band Frequency
(Enhanced Display)
Sub-scope
Main Band Frequency
Sub-band Frequency
Sub-scope
Operating Band Frequency
(Enhanced Display)
Sub-scope
Operating Band Frequency
Dial
Sub-scope
Operating Band Frequency
(Enhanced Display)
Sub-scope
Main Band Frequency
Sub-band Frequency
Main Band Frequency
Sub-band Frequency
(Enhanced Display)