Kenwood TS-990S - Manual (Page 287)

19-3
MISCELLANEOUS 19
Contents
INDEX
A
ABOUT FIRMWARE UPDATING ....................................17-1
ABOUT THE GPL/LPGL LICENSE ....................................IV
ABOUT THE URL AND CONTACTS OF JVC KENWOOD
CORPORATION ..................................................................V
ABOUT THE USB FLASH DRIVE ..................................12-1
ABOUT THIS MANUAL ...................................................... III
ACC2 CONNECTOR ......................................................1-11
ACCESSORIES CONNECTIONS (FRONT PANEL) ........1-2
ACTIVATING AUDIO PEAK FILTER FOR USE IN CW MODE ......6-7
ADJUSTING THE AF GAIN ..............................................4-7
ADJUSTING THE BEEP VOLUME .................................16-5
ADJUSTING THE MICROPHONE GAIN ...............4-17, 5-14
ADJUSTING THE MICROPHONE GAIN FOR FM MODE
OPERATION ..................................................................5-28
ADJUSTING THE REFERENCE LEVEL ..........................7-1
ADJUSTING THE RF GAIN ..............................................4-8
ADJUSTING THE RTTY THRESHOLD LEVEL OF PSK
DECODING ....................................................................5-51
ADJUSTING THE RTTY THRESHOLD LEVEL OF RTTY
DECODING ....................................................................5-37
ADJUSTING THE SIDETONE AND PITCH FREQUENCY ....5-16
ADJUSTING THE SPEECH PROCESSOR INPUT LEVEL ......9-6
ADJUSTING THE SQUELCH LEVEL ...............................4-8
ADJUSTING THE TX POWER .......................................4-17
AFC (AUTOMATIC FREQUENCY CONTROL)...............5-53
AGC (AUTOMATIC GAIN CONTROL) .............................5-4
ANTENNA INSTALLTION AND CONNECTION ...............1-1
APO (AUTOMATIC POWER OFF) .................................15-7
APPLYING THE UPPER LIMIT FREQUENCY OR LOWER LIMIT
FREQUENCY FOR CENTER MODE TO FIX MODE ..............7-5
ATTENUATOR (ATT) ........................................................6-1
AUDIO FILES .................................................................13-7
AUDIO PEAK FILTER .....................................................5-47
AUDIO PEAK FILTER WHILE IN FSK MODE ...................6-9
AUDIO SOURCE LINES FOR TX AUDIO .......................5-11
AUTOMATICALLY CHANGING MODE FROM SSB FOR CW
TRANSMISSION ............................................................5-18
AUTO MODE..................................................................4-11
AUTO NOTCH FILTER (SSB) .........................................6-11
AUTO ZERO-IN (CW AUTO TUNE) ...............................5-17
AVERAGING THE WAVEFORM DISPLAY ON THE
BANDSCOPE ..................................................................7-7
ANNOUNCE LANGUAGE CONFIGURATION ...............14-1
ANNOUNCE VOLUME CONFIGURATION ....................14-1
AUDIO SCOPE ................................................................8-1
AUDIO SCOPE SPAN WIDTH .........................................8-2
AUTO ANNOUNCE CONFIGURATION .........................14-2
B
BAND ELIMINATION FILTER .........................................6-12
BANDSCOPE ..................................................................7-1
BEAT CANCELLER (SSB, AM AND FM) .......................6-14
BANDSCOPE ..................................................................7-1
C
CALBRATING THE INTERNAL REFERENCE FREQUENCY ....18-1
CALIBRATION PROCEDURE ........................................18-1
CAPTURING AND SAVING SCREEN IMAGES ...........16-12
CARRIER FREQUENCY OFFSET WHEN CHANGING
FROM SSB MODE TO CW MODE .................................5-17
CHANGING A FILE NAME IN THE USB FLASH DRIVE ....12-4
CHANGING THE AF FILTER TYPE ..................................6-5
CHANGING THE ANTENNA ..........................................4-20
CHANGING THE ATTENUATOR FOR THE AUDIO SCOPE........8-1
CHANGING THE ATTENUATOR FOR THE BANDSCOPE .....7-8
CHANGING THE AUDIO SCOPE FREQUENCY DISPLAY
SPAN ...............................................................................8-2
CHANGING THE AUDIO SOURCE FOR THE AUDIO
SCOPE ............................................................................8-1
CHANGING THE CUTOFF FREQUENCIES (LOW AND
HIGH FREQUENCIES) TO ADJUST THE PASSBAND
WIDTH CHARACTERISTICS ...........................................6-6
CHANGING THE DISPLAYED FREQUENCY SPAN
(CENTER MODE) ............................................................7-3
CHANGING THE DISPLAY OF THE BANDSCOPE (MAIN
BAND AND SUB BAND) ..................................................7-2
CHANGING THE IF FILTER BANDWIDTH
CHARACTERISTICS .......................................................6-2
CHANGING THE LEVEL OF THE OSCILLOSCOPE .......8-2
CHANGING THE NUMBER OF BAND MEMORIES ........4-9
CHANGING THE PASSBAND CHARACTERISTICS OF THE
AUDIO PEAK FILTER (APF) .............................................6-8
CHANGING THE PASSBAND WIDTH AND AMOUNT OF
SHIFT TO ADJUST PASSBAND CHARACTERISTICS ........6-7
CHANGING THE RECEIVE FREQUENCY USING YOUR
FINGERTIP (CENTER MODE).........................................7-4
CHANGING THE RECEIVE FREQUENCY USING YOUR
FINGERTIP (FIX MODE) ..................................................7-5
CHANGING THE SWEEP TIME .......................................8-3
CLEARING A QUICK MEMORY CHANNEL ..................10-9
CLEARING THE MEMORY CHANNEL ..........................10-7
CLOSING THE MENU .....................................................3-1
COM CONNECTOR .......................................................1-10
COMMON OPERATION IN THE MENU SCREEN ...........3-1
CONFIGURATION FOR PSK ENCODING AND DECODING ....5-59
CONFIGURATION FOR RTTY ENCODING AND
DECODING ....................................................................5-42
CONFIGURING FOR THE ROOOFING FILTER ADDED BY
YOU (MAIN BAND ONLY) ............................................16-22
CONFIGURING IN QUICK MEMORY ............................10-8
CONFIGURING NAMES FOR MEMORY CHANNELS .....10-7
CONFIGURING THE AFC TUNING RANGE ..................5-54
CONFIGURING THE AUTOMATIC TRANSMISSION AND
RECEPTION FOR THE RTTY MESSAGE MEMORY ........5-41
CONFIGURING THE AUTOMATIC TRANSMISSION AND
RECEPTION USING THE RTTY MESSAGE MEMORY ........5-42
CONFIGURING THE CARRIER LEVEL .........................5-13
CONFIGURING THE DATE AND TIME ..........................15-1
CONFIGURING THE I/O SIGNALS FOR THE ACC 2
CONNECTOR ..............................................................16-20
CONFIGURING THE I/O SIGNALS FOR THE OPTICAL
DIGITAL CONNECTOR ................................................16-19
CONFIGURING THE I/O SIGNALS FOR THE USB
CONNECTOR ..............................................................16-21
CONFIGURING THE LENGTH OF TIME FOR KEY LONG
PRESS ...........................................................................16-5
CONFIGURING THE LOWER AND UPPER LIMIT ..........7-5
CONFIGURING THE NETWORK ................................16-12
CONFIGURING THE NUMBER OF QUICK MEMORY
CHANNELS ...................................................................10-9
CONFIGURING THE OPERATING BAND .......................4-8
CONFIGURING THE OUTPUT TO AN EXTERNAL METER ...16-15
CONFIGURING THE POLARITY FOR ACC 2 KEYING .....5-47
CONFIGURING THE POWER-ON MESSAGE ..............16-1
CONFIGURING THE PROGRAM SCAN FREQUENCY
RANGE ..........................................................................10-7
CONFIGURING THE REF I/O CONNECTOR ..............16-22
CONFIGURING THE RESOLUTION OF THE EXTERNAL
MONITOR ....................................................................16-18
CONFIGURING THE SCREEN SAVER .........................16-1
CONFIGURING THE SCREEN SAVER WAIT TIME .......16-2