Kenwood TS-990S - Manual (Page 241)

USEFUL FUNCTIONS 16
16-9
Index Contents
Parameter Operation and activation of function assigned
NB1 SEL (Sub
Band)
Press to open the Noise Blanker 1 (Sub Band)
screen. The transceiver does not behave even if you
press and hold this PF key.
NB2 SEL (Sub
Band)
Press to open the Noise Blanker 2 (Sub Band)
screen. The transceiver does not behave even if you
press and hold this PF key.
NR1 SEL (Sub
Band)
Press and hold to open the Noise Reduction
1 (Sub Band) screen for the sub band. The
transceiver does not behave even if you press and
hold this PF key.
NR2 SEL (Sub
Band)
Press and hold to open the Noise Reduction
2 (Sub Band) screen for the sub band. The
transceiver does not behave even if you press and
hold this PF key.
APF/SEL (Sub
Band)
Press to open the Audio Peak Filter screen for the
sub band. The transceiver does not behave even if
you press and hold this PF key.
MUTE (Sub Band) Press to mute the audio of the sub band.
VOICE 1 (Main
Band)
Press to enable the voice guidance of the main band
frequency.
This is the default for Menu 17, "VOICE (Main Band):
Key Assignment".
VOICE 2
Press to emit a voice guidance, such as a value for
the signal strength of the selected band during the
receive, and a value for transmit power during the
transmit.
This is the default for Menu 15, "PF A Key: Key
Assignment".
VOICE 3
Press to emit a voice guidance, such as a value of
the selected with [METER] (F). The transceiver does
not emit the voice guidance during the reception.
This is the default for Menu 16, "PF B Key: Key
Assignment".
VOICE 1 (Sub
Band)
Press to enable the voice guidance of the sub band
frequency.
This is the default for Menu 18, "VOICE (Sub Band):
Key Assignment".
DSP MONITOR
While you are holding down this key, the passband
width of the IF filter is expanded to maximum.
RX MONITOR
While you are holding down this key, the squelch
opens.
TX TUNE Press to start the TX tuning.
DATA SEND
Press to transmit the signal entered via the
modulation source (rear panel) configured for each
audio source.
SEND
Press to place the transceiver into a transmit state.
Press again to revert the transceiver to the original
state.
DATA VOX/SEL
Each time you press this key, the modulation line
cycles as follows: Off > ACC 2 > USB > OPT.
Press and hold to open the Modulation Source
screen.
Message Memory
CH1
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
channel 1.
This is the default for Menu 19, "External PF 1: Key
Assignment".
Message Memory
CH2
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
channel 2.
This is the default for Menu 20, "External PF 2: Key
Assignment".
Message Memory
CH3
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
channel 3.
This is the default for Menu 21, "External PF 3: Key
Assignment".
Message Memory
CH4
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
channel 4.
This is the default for Menu 22, "External PF 4: Key
Assignment".
Parameter Operation and activation of function assigned
Message Memory
CH5
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
channel 5.
This is the default for Menu 23, "External PF 5: Key
Assignment".
Message Memory
CH6
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
channel 6.
This is the default for Menu 24, "External PF 6: Key
Assignment".
Message Memory
CH7
Press to transmit the CW message, FSK message,
or PSK message stored in channel 7.
This is the default for Menu 25, "External PF 7: Key
Assignment".
Message Memory
CH8
Press to transmit the CW message, FSK message,
or PSK message stored in channel 8.
This is the default for Menu 26, "External PF 8: Key
Assignment".
Contest Number
Decrement
Press to subtract the contest number by one. (CW
Mode)
SWL Press to place the transceiver into SWL mode.
RF Scope Press to display the bandscope.
AF Scope Press to display the audio scope.
Waterfall Press to display the waterfall.
Extended Memory
Channel
Press to invoke the Extended Memory Channel.
Down Key
(Microphone)
Press to operate the transceiver in the same
manner as when the [DOWN] key of the optional
microphone is pressed.
This is the default for Menu 31, "Microphone DOWN:
Key Assignment".
Up Key
(Microphone)
Press to operate the transceiver in the same manner
as when the [UP] key of the optional microphone is
pressed.
This is the default for Menu 32, "Microphone UP:
Key Assignment".
Capture
Press to capture the screen images in the main
screen and the sub-screen and save them as image
files to a USB flash drive.
Safe Removal of
the USB Flash
Drive
Press to execute Safe Removal of the USB Flash
Drive
Emergency
Frequency
Press to call using the frequency allocated to notify
the emergency call frequency on the main band.
Off Nothing is activated.