Kenwood TS-990S - Manual (Page 188)

10 MEMORY CHANNELS
10-6
Index Contents
■ Copy the Memory Channel Data to VFO on the
Memory Channel List Screen.
1 Press [M.LIST] (F7) to open the Memory Channel
List screen.
2 Press [ ] (F2) or [ ] (F3), or rotate the
MULTI/CH control to select a Memory Channel.
3 Press [M V] or [ ] (F6) to copy the operating
data to VFO.
• When the operating data is copied to VFO, the current
operating data in VFO will be cleared.
• The Memory Channel mode ends and enters to VFO
mode.
• You cannot copy operating data from a Program Memory
Channel to the VFO.
• If "S" appears on the "Type" field in the Memory Channel
List screen while in VFO mode, the operating data
configured in "Frequency 1" is copied to the VFO of the
selected band.
• If "D" appears on the "Type" field in the Memory Channel
List screen while in VFO mode, the operating data
configured in "Frequency 1" is copied to the main band,
the operating data configured in "Frequency 2" is copied to
the sub band, and the operating status in "TX/RX Freq." is
copied to VFO.
4 Press [ESC] to exit.
COPYING OPERATING DATA FROM ONE MEMORY
CHANNEL TO ANOTHER MEMORY CHANNEL
(CHANNEL TO CHANNEL)
You can copy the operating data in a Memory Channel
to another Memory Channel. It is useful when sorting the
order of the configured Memory Channels.
1 Press [M.LIST] (F7) to open the Memory Channel
List screen.
2 Press [ ] (F2) or [ ] (F3), or rotate the
MULTI/CH control to select the Memory Channel to
copy the operating data.
3 Press [COPY] (F6) to copy the operating data.
• If [COPY] (F6) is unavailable in the function key guide,
press [MORE] (F1).
• The Memory Channel to be copied is highlighted in pink.
4 Press [ ] (F2) or [ ] (F3), or rotate the
MULTI/CH control to select the Memory Channel to
configure the copied operating data.
5 Press [M.IN] (F4) to exit.
• The operating data in the Memory Channel selected in
step 2 is copied to the Memory Channel selected at step 4.
• Press [CANCEL] (F1) or [ESC] to exit without copying the
operating data.
Note:
◆ You cannot copy the operating data in typical Memory Channels
and extensive Memory Channels (00 to 99, E0 to E9) to Program
Memory Channels (P0 to P9). You cannot copy in the reverse
direction either.
◆ You cannot copy operating data from a Memory Channel with no
operating data configured.
COPYING OPERATING DATA FROM THE
MEMORY CHANNEL
You can copy the operating data from a Memory Channel
to VFO or to another Memory Channel.
[ESC] [MULTI/CH] [F1] [F7]
MEMORY SHIFT (MEMORY TO VFO)
You can copy the operating data from a Memory Channel
to VFO. It is useful when the frequency to be used is
similar to the frequency configured in a Memory Channel.
■ Select a Memory Channel and Copy Its Data to
VFO.
1 In Memory Channel mode, rotate the MULTI/CH
control to select a Memory Channel.
2 Press [M V] or [ ] (F6) to copy the operating
data to VFO.
• The operating data in the selected Memory Channel is
copied to VFO.
• The Memory Channel mode ends and enters to VFO
mode.
• If an operating data is changed temporarily, the changed
operating data is copied to VFO.
• You cannot copy operating data from a Program Memory
Channel to the VFO.
• In Single-band Memory Channel mode, the operating data
configured in "Frequency 1" is copied to the VFO of the
selected band.
• In Dual-band Memory Channel mode, the operating data
configured in "Frequency 1" is copied to the main band,
the operating data configured in "Frequency 2" is copied to
the sub band, and the operating status in "TX/RX Freq." is
copied to VFO.