Kenwood TS-990S - Manual (Page 43)

3-1
3 MENU
Index Contents
MENU CONFIGURATIONS
In the Menu screen, you can configure and edit various
functions of this transceiver as well as change the
operating environment.
This transceiver's Menu contains common functions and
configurations, along with 5 sub menus categorized for
those sub menu groups.
[ESC] [F1] [F7]
F[RESET]
F[AUTO MODE] F[USB DRIVE]
F[CLOCK] F[LAN]
F[ADV.] [MENU]
[UP]
[＜MAIN ] [SUB＞]
[DOWN]
[MULTI/CH]
OPENING THE MENU
1 Press [MENU] to open the Menu screen.
Displays the acquired IP address.)
Displays the operating environment (CONFIG A or CONFIG B).
The menu group number and the menu items appear.
2 Press [ ] (F2) or [ ] (F3) to select a
group.
3 Press [SELECT] (F4) or [SUB>] to display the menu
items of the selected group.
4 Press [ ] (F2) or [ ] (F3) to select a
menu item.
5 Press [SELECT] (F4) or [SUB>] to allow editing of the
parameter box.
The parameter box becomes active, and the parameter can
be changed.
6 Press [–] (F4) or [+] (F5) to select a parameter.
The parameter for the menu item varies.
7 Press [ ] (F1) to revert to the previous screen.
The selected parameter has determined.
8 Press [MENU] to end.
OPENING THE SUB MENU
1 Press [MENU] to open the Menu screen.
2 Press the function key for the key guide on the right
side of the main screen.
Following are the sub menu that appears on the screen.
Sub Menu Key Guide Summary of Changes
Reset RESET
A menu which allows you to reset the
transceiver to its default state.
Clock CLOCK
A menu which allows you to configure
the internal clocks.
LAN LAN
A menu which allows you to configure
the connections to your LAN.
AUTO MODE AUTO MODE A menu which allows you to configure
the upper and lower limit frequencies.
Advanced ADV.
An advanced menu that allows detailed
advanced configurations including
connections to external devices.
SWL SWL
A key which activates and displays
“Short Wave Listener” style horizontal
dials with a vertical meter.
USB Flash
Drive
USB DRIVE A menu which allows you to manage a
USB flash drive.
COMMON OPERATION IN THE MENU SCREEN
• Pressing [MENU TOP] (F) reverts to the Menu screen.
• Press [
] (F2) or [ ] (F3) to scroll
through the menu groups.
• Each menu can be selected with the operation below.
• Rotate the MULTI/CH control.
• Press [
] (F2) or [ ] (F3).
Press [UP] or [DOWN].
• The parameter for the menu item with an editable
parameter box can be selected as follows:
• Rotate the MULTI/CH control.
• Press [UP] or [DOWN].
• Press [–] (F4) or [+] (F5).
• Press [
] or [ ].
• Press the [UP] or [DOWN] (microphone).
• Pressing and holding [(RESET)] (F1) reverts the
parameters to their defaults.
CLOSING THE MENU
If you finish the configuration or edit in the Menu screen,
or if you wish to finish the operation during the menu item
configuration, follow the procedure below. The Menu
screen closes, the normal screen reappears.
1 Press [MENU] or [ESC].
Note:
◆ All configurations in the Menu screen can be reset to the default
parameters. {page 16-4}
◆ Menu contents, such as the menu item name and default
parameters, are subject to change due to design change and
innovations.
◆ During configuration of the screen saver or the power-on message,
pressing [MENU] does not close the Menu screen.