Document Outline

• 9499 050 52201
• Table of Contents
• 1 Safety Information
  • 1.1 General Information
  • 1.2 Intended Use
  • 1.3 Initial Inspection
  • 1.4 Before Commissioning
    • 1.4.1 Installation
    • 1.4.2 Electrostatically Sensitive Components
    • 1.4.3 Protective Earth
    • 1.4.4 Supply Voltage Connection
    • 1.4.5 Failure and Excessive Stress
    • 1.4.6 Fuse
    • 1.4.7 EMC-Compliant Installation
• 2 Ethernet Transmitter Series
  • 2.1 The Transmitter Versions
    • 2.1.1 PR 5220/00 Version
    • 2.1.2 PR 5220/01 ProfibBus
    • 2.1.3 PR 5220/04 DeviceNet
    • 2.1.4 PR 5220/06 ProfiNet I/O
    • 2.1.5 PR 5220/07 EtherNet-IP
  • 2.2 Overview of the Instrument
  • 2.3 Label on the Housing
  • 2.4 Housing Dimensions
  • 2.5 Display and Controls
    • 2.5.1 Status LEDs
      • 2.5.1.1 Power Supply, Bus Connection
      • 2.5.1.2 Weight Status Indicator
    • 2.5.2 Operation Using the VNC Program
      • 2.5.2.1 Operator Interface
      • 2.5.2.2 Status Symbols
      • 2.5.2.3 Keys
      • 2.5.2.4 Operation Using Softkeys
      • 2.5.2.5 Selection Using the Navigation Keys
  • 2.6 Overview of Connections
• 3 Installing the Instrument
  • 3.1 Connections
    • 3.1.1 Network Port
    • 3.1.2 RS-485 Interface
      • 3.1.2.1 Connecting of a PR 5110 Remote Display
      • 3.1.2.2 Connection of a xBPI Platform XE "xBPI platform over RS-485"
      • 3.1.2.3 Connection of a xBPI terminal XE "xBPI terminal over RS-485"
      • 3.1.2.4 Connecting 4 Digital Load Cells Type ‚Pendeo®‘ XE "Digital load cells via RS-485"
    • 3.1.3 Analog Output
    • 3.1.4 Optocoupler Inputs
    • 3.1.5 Optocoupler Outputs
    • 3.1.6 Load Cell Connection
      • 3.1.6.1 Connection Using 6-Wire Technology
      • 3.1.6.2 Connection of a Load Cell in 4-Wire Technology
      • 3.1.6.3 Connecting PR 6221 Load Cells
      • 3.1.6.4 External Load Cell Supply
      • 3.1.6.5 Connection via Intrinsically Safe Interface PR 1626/60
    • 3.1.7 Connecting Analog Platforms (CAP...)
    • 3.1.8 Connecting xBPI Platforms (IS...)
    • 3.1.9 Connection of Digital Load Cells
    • 3.1.10 ProfiBus Interface (PR 5220/01 only)
    • 3.1.11 DeviceNet Interface (PR 5220/04 only)
    • 3.1.12 ProfiNet I/O Interface (PR 5220/06 only)
    • 3.1.13 EtherNet-IP Interface (PR 5220/07 only)
• 4 Commissioning
  • 4.1 Data Backup/Power Failure
    • 4.1.1 CAL Switch
    • 4.1.2 Factory Settings
  • 4.2 Switching on the Instrument
  • 4.3 Configuration and Calibration
    • 4.3.1 Connecting the Device to the Network and Finding out the IP address
    • 4.3.2 Resetting the Instrument/Activating Network'DHCP'
      • 4.3.2.1 MAC ID
      • 4.3.2.2 DHCP
      • 4.3.2.3 Host Name (device name)
    • 4.3.3 Searching the Instrument in the Network Using 'IndicatorBrowser'
    • 4.3.4 Operation Using the VNC Program
    • 4.3.5 Operation Using Internet Browser
    • 4.3.6 INFO Function
    • 4.3.7 Setup Function (VNC)
    • 4.3.8 Setup Menu
      • 4.3.8.1 Weighingpoint ‚Internal A’
      • 4.3.8.2 Weighingpoint ‚xBPI-Scale’
      • 4.3.8.3 Weighingpoint ‚ Pendeo Load Cells’
  • 4.4 Calibration Weighing Point ‚Internal A’
    • 4.4.1 Displaying Calibration Data
      • 4.4.1.1 Increased Resolution (10-Fold)
    • 4.4.2 Selecting the Calibration Mode
      • 4.4.2.1 New Calibration
      • 4.4.2.2 Changing the Calibration
    • 4.4.3 Determining the Maximum Capacity (Max)
    • 4.4.4 Determining the Scale Interval
    • 4.4.5 Determining the Dead Load
    • 4.4.6 Calibration with Weight (by Load)
    • 4.4.7 Calibration with mV/V Value [by mV/V]
      • 4.4.7.1 SPAN
      • 4.4.7.2 Dead Load
    • 4.4.8 Calibration with Load Cell Data (“Smart Calibration“)
    • 4.4.9 Subsequent Dead Load Correction
    • 4.4.10 Linearization
    • 4.4.11 Test Value Determination/Display
    • 4.4.12 Finishing/Saving the Calibration
    • 4.4.13 Parameter Input
      • 4.4.13.1 Legal-for-Trade Operation XE "Legal-for-trade operation"
      • 4.4.13.2 Multiple Range Scale/Multi-Interval Scale
  • 4.5 Calibrating an xBPI Scale
    • 4.5.1 xBPI Set-up for Serial Port
    • 4.5.2 xBPI Scale Function
    • 4.5.3 xBPI Platform Configuration
    • 4.5.4 xBPI Scale Parameter
    • 4.5.5 xBPI Parameter Tables
    • 4.5.6 xBPI Setting Dead Load
    • 4.5.7 xBPI Calibration with the User Weight
    • 4.5.8 xBPI Calibration with Automatic Weight Detection
    • 4.5.9 xBPI Calibration with Default Weight
    • 4.5.10 xBPI Calibration with Built-in Weight
  • 4.6 Calibrating Digital Load Cells Type ‘Pendeo®’
    • 4.6.1 General Information
    • 4.6.2 Viewing the Interfaces
    • 4.6.3 Selecting and Setting up the Interface
    • 4.6.4 Selecting the Load Cell Type
    • 4.6.5 Adjustment Sequence
    • 4.6.6 Search for Load Cells
    • 4.6.7 Assigning Load Cells
    • 4.6.8 Calibrating Load Cells
    • 4.6.9 Corner Correction
      • 4.6.9.1 General Information
      • 4.6.9.2 Checking Corner Load (Dead Load)
      • 4.6.9.3 Software Corner Correction
    • 4.6.10 Finishing/Saving the Calibration
    • 4.6.11 Parameter Input
    • 4.6.12 Subsequent Dead Load Correction
  • 4.7 Configuring General Parameters
    • 4.7.1 Serial Interfaces [Serial ports parameter]
    • 4.7.2 Operating Parameters
    • 4.7.3 Fieldbus Parameters
    • 4.7.4 Network Parameters
  • 4.8 Configuring Limit Values
  • 4.9 Digital Outputs and Inputs
    • 4.9.1 Configuring Digital Outputs
    • 4.9.2 Configuring Digital Inputs
  • 4.10 Analog Output
    • 4.10.1 Adapting the Analog Output
  • 4.11 Logfiles
  • 4.12 Saving Configuration Data [Backup of EAROM]
    • 4.12.1 Saving Configuration and Calibration Data
    • 4.12.2 Loading Configuration and Calibration Data into the Device
• 5 J-Bus/ModBus Protocol
  • 5.1 General Description
  • 5.2 ModBus-TCP/-UDP
  • 5.3 Functions
  • 5.4 Error Messages
  • 5.5 Word Addresses
• 6 SMA Protocol
  • 6.1 General
  • 6.2 Description of Used Symbols
  • 6.3 SMA Command Set
  • 6.4 SMA Reply Messages
  • 6.5 Communication Error
• 7 Fieldbus Interface
  • 7.1 Fieldbus Interface Protocol
  • 7.2 Description of the I/O Area (Read / Write Window)
  • 7.3 Special hints for DeviceNet and EtherNet-IP
  • 7.4 Fieldbus Register
• 8 Global SPM Variables
• 9 Configuration Print-Out
• 10 Extended Functions
  • 10.1 Resetting the Instrument to the Factory Settings
  • 10.2 Updating a new Software with ‚FlashIt’
• 11 Repairs and Maintenance
  • 11.1 Solder Work
  • 11.2 Cleaning
• 12 Disposal
• 13 Error Messages
  • 13.1 Measuring Circuit Error Messages
  • 13.2 Weight Error Status
  • 13.3 Error Messages with xBPI Scales
  • 13.4 Error messages of the Calibration
  • 13.5 Show Error Log
• 14 Specifications
  • 14.1 Instructions for Use of 'Free Software'
  • 14.2 General Data
    • 14.2.1 Power Supply
  • 14.3 Effect of Ambient Conditions
    • 14.3.1 Environmental Conditions
    • 14.3.2 Electromagnetic Compatibility (EMC)
    • 14.3.3 RF Interference Suppression
  • 14.4 Weighing Electronics
    • 14.4.1 Load Cells
    • 14.4.2 Principle
    • 14.4.3 Accuracy and Stability
    • 14.4.4 Sensitivity
  • 14.5 Mechanical Data
    • 14.5.1 Construction
    • 14.5.2 Dimensions
    • 14.5.3 Weight
  • 14.6 Use in Legal-for-Trade Mode
    • 14.6.1 Documentation for Verification on the Enclosed CD
    • 14.6.2 Additional Instructions
• 15 Index
• 16 Appendix
  • 16.1 Pin Assignment for Interface RS-485
  • 16.2 Network Settings under Windows XP
  • 16.3 Network Settings under Windows 7