H3C Technologies H3C S5560 Series Switches User Manual

Page 84

Advertising

[DeviceA] vlan 10

[DeviceA-vlan10] port gigabitethernet 1/0/5

[DeviceA-vlan10] quit

# Create VLAN 20, and assign the port GigabitEthernet 1/0/6 to VLAN 20.

[DeviceA] vlan 20

[DeviceA-vlan20] port gigabitethernet 1/0/6

[DeviceA-vlan20] quit

# Create Layer 2 aggregate interface Bridge-Aggregation 1.

[DeviceA] interface bridge-aggregation 1

# Configure Layer 2 aggregation group 1 to load share packets based on source MAC addresses.

[DeviceA-Bridge-Aggregation1] link-aggregation load-sharing mode source-mac

[DeviceA-Bridge-Aggregation1] quit

# Assign ports GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2 to link aggregation group 1.

[DeviceA] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] port link-aggregation group 1

[DeviceA-GigabitEthernet1/0/1] quit

[DeviceA] interface gigabitethernet 1/0/2

[DeviceA-GigabitEthernet1/0/2] port link-aggregation group 1

[DeviceA-GigabitEthernet1/0/2] quit

# Configure Layer 2 aggregate interface Bridge-Aggregation 1 as a trunk port and assign it to

VLAN 10.

[DeviceA] interface bridge-aggregation 1

[DeviceA-Bridge-Aggregation1] port link-type trunk

[DeviceA-Bridge-Aggregation1] port trunk permit vlan 10

[DeviceA-Bridge-Aggregation1] quit

# Create Layer 2 aggregate interface Bridge-Aggregation 2.

[DeviceA] interface bridge-aggregation 2

# Configure Layer 2 aggregation group 2 to load share packets based on destination MAC

addresses.

[DeviceA-Bridge-Aggregation2] link-aggregation load-sharing mode destination-mac

[DeviceA-Bridge-Aggregation2] quit

# Assign ports GigabitEthernet 1/0/3 and GigabitEthernet 1/0/4 to link aggregation group 2.

[DeviceA] interface gigabitethernet 1/0/3

[DeviceA-GigabitEthernet1/0/3] port link-aggregation group 2

[DeviceA-GigabitEthernet1/0/3] quit

[DeviceA] interface gigabitethernet 1/0/4

[DeviceA-GigabitEthernet1/0/4] port link-aggregation group 2

[DeviceA-GigabitEthernet1/0/4] quit

# Configure Layer 2 aggregate interface Bridge-Aggregation 2 as a trunk port and assign it to
VLAN 20.

[DeviceA] interface bridge-aggregation 2

[DeviceA-Bridge-Aggregation2] port link-type trunk

[DeviceA-Bridge-Aggregation2] port trunk permit vlan 20

[DeviceA-Bridge-Aggregation2] quit

Configure Device B in the same way Device A is configured. (Details not shown.)

Advertising

This manual is related to the following products:

H3C S5130 Series Switches, H3C S5120 Series Switches, H3C SR8800, H3C SR6600-X, H3C SR6600, H3C MSR 5600, H3C MSR 50, H3C MSR 3600, H3C MSR 30, H3C MSR 2600, H3C MSR 20-2X[40], H3C MSR 20-1X, H3C MSR 930, H3C MSR 900, H3C WX6000 Series Access Controllers, H3C WX5000 Series Access Controllers, H3C WX3000 Series Unified Switches, H3C LSWM1WCM10 Access Controller Module, H3C LSWM1WCM20 Access Controller Module, H3C LSQM1WCMB0 Access Controller Module, H3C LSRM1WCM2A1 Access Controller Module, H3C LSBM1WCM2A0 Access Controller Module

Popular Brands

Popular manuals