Konica Minolta bizhub PRESS C8000e - Manual (Page 327)

bizhub PRESS C8000/e 9-9
9.1 Function Overview 9
05 Glue Finish Position
Adjust the position to finish gluing on the body set.
The sizes referred to in this section are those of
body sets corresponding to cover sizes. Objects of adjustment:
Ahead (rear): Full Area, A4 v, B5 v, A5 w/v,
8.5 e 11 v, 5.5 e 8.5 w, 16K v, Custom (220-
379 mm), Custom (148-219 mm)
Back (front): Full Area, A4 v, B5 v, A5 w/v,
8.5 e 11 v, 5.5 e 8.5 w, 16K v, Custom (220-
379 mm), Custom (148-219 mm)
Adjustable range:
-128 (Soon) to +127 (Late)
(1 step = 0.1 mm)
06 Temperature Adjustment
Glue Tank -Top*:
The machine supplies glue pellets on detecting the
temperature of solution surface lower than the set
point. It is recommended to be set higher in thermal
environment where the machine tends to fail in de-
tection.
Glue Tank -Mid:
Set the temperature to reach when warm-up is
completed, and to start rotating the roller. Setting it
higher helps glue temperature to be stable sooner.
Glue Tank -Low:
Adjust the temperature to control the tank heater.
Low temperature: Increases glue viscosity.
High temperature: Decreases glue viscosity.
Glue Apply Roller:
Adjust the temperature to control the roller heater.
This also supports heating of the glue.
Low temperature: Increases glue viscosity.
High temperature: Decreases glue viscosity.
*: Contact your service representative if setting
change in Glue Tank - Top and Glue Tank - Mid is
desired. Glue Tank -Top:
Initial: 132°C
Recommended: 128 to 136°C
Glue Tank -Mid:
Initial: 145°C
Recommended: 140 to 145°C
Glue Tank -Low:
Initial: 185°C
Recommended: 180 to 190°C
Glue Apply Roller:
Initial: 165°C
Recommended: 160 to 170°C
(1 step = 0.1°C)
07 Sub Compile CD Width Adj.
Change the adjustment width if output sheets can-
not be aligned in sub compile section. The sizes re-
ferred to in this section are those of body sets
corresponding to cover sizes. Objects of adjustment:
Full Area, A4 v, B5 v, A5 w/v, 8.5 e 11 v, 5.5
e 8.5 w, 16K v, Custom (220-379 mm), Cus-
tom (148-219 mm)
Adjustable range:
-20 (Wide) to +20 (Narrow)
(1 step = 0.1 mm)
08 Clamp CD Width Adjustment
Change the adjustment width in crosswise direc-
tion if output sheets show misalignment in a body
set. The sizes referred to in this section are those of
body sets corresponding to cover sizes. Objects of adjustment:
Full Area, A4 v, B5 v, A5 w/v, 8.5 e 11 v, 5.5
e 8.5 w, 16K v, Custom (220-379 mm), Cus-
tom (148-219 mm)
Adjustable range:
-20 (Wide) to +20 (Narrow)
(1 step = 0.1 mm)
09 Cover Up/Down CD Width Adj.
Change the adjustment width in matching body
sets and covers, in order to adjust their positions in
crosswise direction. Objects of adjustment:
Perfect Binder Tray, Except PB Tray
Adjustable range:
-20 (Wide) to +20 (Narrow)
(1 step = 0.1 mm)
10 Clamp FD Position Adj.
Change the adjustment width in paper feed direc-
tion if output sheets show misalignment in a body
set. The sizes referred to in this section are those of
body sets corresponding to cover sizes. Objects of adjustment:
Full Area, A4 v, B5 v, A5 w/v, 8.5 e 11 v, 5.5
e 8.5 v, 16K v, Custom (220-379 mm), Cus-
tom (148-219 mm)
Adjustable range:
-20 (Wide) to +20 (Narrow)
(1 step = 0.1 mm)
Menu Item/Description Objects/Range