Konica Minolta bizhub PRESS C8000e - Manual (Page 427)

bizhub PRESS C8000/e 10-13
10.1 Utility Menu Screen Outlines 10
[03 Staple Pitch Adjustment]
Adjust the staple pitch determined by
the saddle stitcher. Objects of adjustment:
Full Area, SRA3 w, A3 w, B4 w, SRA4 w,
A4 w, B5 w, 13 e 19 w, 12 e 18 w, 11 e
17 w, 8.5 e 14 w, 8.5 e 11 w, 8.125 e
13.25 w, 8.5 e 13 w, 8.25 e 13 w, 8 e 13
w, 8K w, 16K w, Custom (380-463 mm),
Custom (257-379 mm)
Adjustable range:
-20 (Narrow) to +20 (Wide)
(1 step = 1.0 mm)
[04 Half-Fold Position Adj.]
Adjust the half-folded position deter-
mined by the saddle stitcher. Objects of adjustment:
Full Area, SRA3 w, A3 w, B4 w, SRA4 w,
A4 w, B5 w, 13 e 19 w, 12 e 18 w, 11 e
17 w, 8.5 e 14 w, 8.5 e 11 w, 8.125 e
13.25 w, 8.5 e 13 w, 8.25 e 13 w, 8 e 13
w, 8K w, 16K w, Custom (380-463 mm),
Custom (257-379 mm)
Adjustable range (top of output sheet):
-50 (Short) to +50 (Long)
(1 step = 0.1 mm)
[05 Tri-Fold Position Adj.]
Adjust the folded positions in Tri-Fold-
in mode determined by the saddle
stitcher.
The position of Single Fold is calculat-
ed from the edge of the sheet, while
that of Double Fold is calculated from
the position of Single Fold. Be sure to
start with the Double Fold adjustment,
then proceed to the Single Fold adjust-
ment. Objects of adjustment:
Full Area, A4 w, 8.5 e 11 w
Adjustable range:
Single Fold: -100 (Short) to +100 (Long)
(1 step = 0.1 mm)
Double Fold: -100 (Long) to +100 (Short)
(1 step = 0.1 mm)
[06 Fold Paper Width Adj.]
Adjust the width of adjustment plates if
half-folded or tri-folded sheets show
misalignment. Objects of adjustment:
Full Area, SRA3 w, A3 w, B4 w, SRA4 w,
A4 w, B5 w, 13 e 19 w, 12 e 18 w, 11 e
17 w, 8.5 e 14 w, 8.5 e 11 w, 8.125 e
13.25 w, 8.5 e 13 w, 8.25 e 13 w, 8 e 13
w, 8K w, 16K w, PI, Custom (380-463
mm), Custom (257-379 mm)
Adjustable range:
-50 (Narrow) to +50 (Wide)
(1 step = 0.1 mm)
[07 Trimming Adjustment]
Adjust the trimming width. The trim-
ming width should be more than 2.0
mm, otherwise the trimming operation
may not performed properly. Objects of adjustment:
Full Area, SRA3 w, A3 w, B4 w, SRA4 w,
A4 w, B5 w, 13 e 19 w, 12 e 18 w, 11 e
17 w, 8.5 e 14 w, 8.5 e 11 w, 8.125 e
13.25 w, 8.5 e 13 w, 8.25 e 13 w, 8 e 13
w, 8K w, 16K w, Custom (380-463 mm),
Custom (257-379 mm)
Adjustable range:
-400 (Short) to +400 (Long)
(1 step = 0.1 mm)
[08 Trimmer Receiver Adjustment]
Frequent trimming operations may
cause damage to the receiver, resulting
in trimming failures. Move the receiver
automatically or manually. Objects of adjustment:
Trim Count, Move Pitch
Menu Item/Description Setting options (with default bolded)