Rear panel, 2−names and functions of parts – Teac HS-2 User Manual
Page 14
14
TASCAM HS-2
Rear panel
g
ANALOG INPUTS L/R (UNBALANCED) connectors
These connectors are analog unbalanced inputs L-R
(RCA pin jack) The rated input level is -10dBV.
h
ANALOG INPUTS L/R (BALANCED) connectors
These connectors analog are balanced inputs L-R
(XLR balance) The rated input level is +4dBu.
(1: GND, 2: HOT, 3: COLD)
j
DIGITAL IN (S/PDIF) connector
This connector is an unbalanced input for digital audio
in IEC60958-3(S/PDIF) and AES3-2003 / IEC60958-4
(AES/EBU) format.
Sampling frequencies of 88.2 kHz and 96 kHz are trans-
mitted at double speed, and 176.4 kHz and 192 kHz
are at quad speed.
This unit is equipped with a sampling rate converter
which supports 32 kHz to 192 kHz.
k
DIGITAL IN (AES/EBU) connector
This connector is an XLR balanced input for digital
audio in AES3-2003 / IEC60958-4 (AES/EBU) and
IEC60958-3 (S/PDIF) format.
Sampling frequencies of 88.2 kHz and 96 kHz are trans-
mitted at double speed, and 176.4 kHz and 192 kHz
are at quad speed.
This unit is equipped with a sampling rate converter
which supports 32 kHz to 192 kHz.
l
REMOTE connector
Connect a TASCAM RC-HS20PD remote control (sold
separately) here.
NOTE
A Protective cover is attached to this connector when
shipped from the factory. Remove the cover before
connecting the remote control.
CAUTION
This is not an Ethernet connector (LAN, etc.). Never
connect this to a network using an Ethernet cable. Doing
so could damage this unit or equipment in the network.
;
RS-232C connector
Connect an external controller, for example, to this
9-pin D-sub connector for RS-232C serial control.
NOTE
• It cannot be used at the same time as the RS-422
connector. (See “RS–232C page” on page 96.)
z
PARALLEL connector
Connect an external controller (such as the TASCAM
RC-SS20), for example, to this 25-pin D-sub parallel
control connector.
x
AC IN connector
Connect the included power cord here.
c
ANALOG OUTPUTS L/R (UNBALANCED) connectors
These connectors are analog unbalanced outputs L-R
(RCA pin jack). The rated output level is -10dBV.
v
ANALOG OUTPUTS L/R (BALANCED) connectors
These connectors analog are balanced outputs L-R (XLR
balance). The rated output level is +6dBu when setting
Digital Ref. Level to – 9dBu and +4dBu for other cases.
(1:GND, 2:HOT, 3:COLD)
b
DIGITAL OUT (S/PDIF) connector
This connector is an unbalanced output for digital
audio in IEC60958-3(S/PDIF) format.
Sampling frequencies of 88.2 kHz and 96 kHz are trans-
mitted at double speed, and 176.4kHz and 192 kHz
are at quad speed.
n
DIGITAL OUT (AES/EBU) connectors
This connector is an XLR balanced output for digital
audio in AES3-2003 / IEC60958-4 (AES/EBU) format.
Sampling frequencies of 88.2 kHz and 96 kHz are trans-
mitted at double speed, and 176.4 kHz and 192 kHz
are at quad speed.
m
RS-422 connectors (Attached to Option SY-2 Board)
Connect an external controller, for example, to this
9-pin D-sub connector for RS-422 serial control.
NOTE
It cannot be used at the same time as the RS-232C
connector. (See “RS–422 page” on page 96.)
,
TIME CODE IN/OUT connectors (Attached to Option
SY-2 Board)
This connector is a balanced input/ output for SMPTE
timecode input/output of BNC type.
2−Names and functions of parts