H3C Technologies H3C S12500 Series Switches User Manual
Layer 2—lan switching configuration guide
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- Title Page
- Preface
- Contents
- Configuring VLANs
- Configuring the super VLAN
- Configuring the voice VLAN
- Overview
- Configuration prerequisites
- Configuration guidelines
- Configuring QoS priority settings for voice traffic on an interface
- Configuring a port to operate in automatic voice VLAN assignment mode
- Configuring a port to operate in manual voice VLAN assignment mode
- Displaying and maintaining voice VLAN
- Voice VLAN configuration examples
- Configuring the MAC address table
- Overview
- Configuring static, dynamic, and blackhole MAC address table entries
- Configuring a multiport unicast MAC address table entry
- Configuring the aging timer for dynamic MAC address entries
- Configuring the MAC learning limit
- Enabling MAC address migration log notifying
- Displaying and maintaining the MAC address table
- MAC address table configuration example
- Configuring spanning tree protocols
- STP
- RSTP
- PVST
- MSTP
- Protocols and standards
- Spanning tree configuration task lists
- Setting the spanning tree mode
- Configuring an MST region
- Configuring the root bridge or a secondary root bridge
- Configuring the switch priority
- Configuring the maximum hops of an MST region
- Configuring the network diameter of a switched network
- Configuring spanning tree timers
- Configuring the timeout factor
- Configuring the maximum port rate
- Configuring edge ports
- Configuring path costs of ports
- Configuring the port priority
- Configuring the port link type
- Configuring the mode a port uses to recognize/send MSTP packets
- Enabling the spanning tree feature
- Performing mCheck
- Configuring the VLAN Ignore feature
- Configuring Digest Snooping
- Configuring No Agreement Check
- Configuring TC snooping
- Configuring protection functions
- Displaying and maintaining the spanning tree
- Spanning tree configuration examples
- Configuring Ethernet link aggregation
- Overview
- Ethernet link aggregation configuration task list
- Configuring an aggregation group
- Configuring an aggregate interface
- Configuring the description of an aggregate interface/subinterface
- Configuring the MTU of a Layer 3 aggregate interface/subinterface
- Enabling link state trapping for an aggregate interface
- Limiting the number of Selected ports for an aggregation group
- Shutting down an aggregate interface
- Restoring the default settings for an aggregate interface
- Configuring load sharing for link aggregation groups
- Enabling link-aggregation traffic redirection
- Enabling link aggregation enhancement in IRF mode
- Displaying and maintaining Ethernet link aggregation
- Ethernet link aggregation configuration examples
- Configuring port isolation
- Configuring QinQ
- Configuring VLAN mapping
- Configuring BPDU tunneling
- Configuring GVRP
- Overview
- GVRP configuration task list
- Configuring GVRP functions
- Configuring GARP timers
- Displaying and maintaining GVRP
- GVRP configuration examples
- Configuring loopback detection
- Configuring VLAN termination
- Overview
- VLAN termination configuration task list
- Configuring QinQ termination
- Enabling a VLAN termination-enabled interface to transmit broadcast and multicast packets
- Configuring the TPID for VLAN-tagged packets
- VLAN termination configuration examples
- Configuring MAC-in-MAC
- Configuring LLDP
- Overview
- LLDP configuration task list
- Performing basic LLDP configuration
- Configuring CDP compatibility
- Configuring LLDP trapping
- Displaying and maintaining LLDP
- LLDP configuration examples
- Configuring MVRP
- Overview
- MVRP configuration task list
- Configuring MVRP
- Configuring MRP timers
- Enabling GVRP compatibility
- Displaying and maintaining MVRP
- MVRP configuration examples
- Index