Toa N-8000 Series Ver.1.41 - Manual (Page 95)

2-43
Chapter 2: FUNCTIONS AND OPERATION
5. MASTER STATION OPERATION TABLE
Call/Response
Conversation
Speed dialing
Hold
Call transfer
Call
forwarding
Time-based
call
forwarding
Absence
transfer
Group
hunting
Remote response
Executive priority
Scan monitor
Paging
Paging Response
Station speaker
output settings
Ambient Noise Control
Door remote
Call
Redialing
Recall
Voice Calling
Response
Handset conversation
Hands-free conversation
PTT conversation
Auto-dialing
One-touch dialing
Mic Off
Call hold
Call hold release
Call transfer
Returning to the
original conversation
Programming
at your station
Erasure at your station
Programming
at the designated station
Programming
Erasure
Programming
Erasure
Programming
Erasure
Start
Stop/Restart
Advancing Scan
Reverse Scan
Voice transmission
End
Zone paging
Selectable paging
All-call paging
Automatic Response
Zone number dialing
Increase volume
Decrease volume
Dial station No. XXXX
Press the [Redial] key
Press the [ ] key
Voice a call to a called party by pressing the [PTT] key as the
continuous call tone sounds.
Press any key or lift the handset.
Conversation can be made by lifting the handset.
Conversation can be made without lifting the handset.
Press the [PTT] key during a hands-free conversation.
Press the Auto-dialing key ( [1] – [8].)
Press [7] , [8] , [9] , [0] or lift the handset.
Continuously hold down any key ( [0] – [9] ) during a conversation.
Press the [Hold] key during a conversation.
Press the [Hold] key during hold.
Press the [Transfer] key during a conversation.
The other party is placed on hold.
Dial the third party's station number.
Conversation with the third party.
(Original conversation party is placed on hold).
Either press the [C] key or replace the handset.
Call transfer completion
Press the [Transfer] key during a conversation.
The other party is placed on hold.
Dial the third party's station number.
Conversation with the third party.
(The original conversation party is placed on hold).
Press the [Transfer] key again.
Return to the original conversation.
(The original conversation is restored).
Dial [Function] [4] [1] [the designated station No.] [ ] keys.
Dial [Function] [4] [1] [your station No.] [ ] keys.
Dial [Function] [4] [2] [your station No.][ ] keys.
Dial [Function] [4] [3] [the designated station No.] [ ] keys.
Dial [Function] [4] [3] [your station No.] [ ] keys.
Dial [Function] [4] [4] [the designated station No.] [ ] keys.
Dial [Function] [4] [4] [your station No.] [ ] keys.
Dial [Function] [4] [5] [the designated station No.] [ ] keys.
Dial [Function] [4] [5] [your station No.] [ ] keys.
When call is received to the station assigned to the
same group, press the [PTT] key.
If a called station is busy, press the [9] key.
Dial [ ] [2] [Monitor group No.]
[Monitor group No.] [ ] keys.
Press [0] to stop. Press [0] again to restart.
Press [ ] key to advance the scan by one station.
Press [ ] key to move the scan back one station.
Press [PTT] to establish conversation.
Either press the [C] key or replace the handset.
Dial [Paging] [Zone No.] keys.
Dial [ ] [Zone No.] [ ] [Zone No.]
[ ] [Zone No.] [ ] keys.
Dial [Paging] [0] keys.
Press [Paging Response] key.
Dial [Paging Response] [Zone No.] keys.
Press [ ] key during a conversation.
Press [ ] key during a conversation.
Dial [ ] [ ] keys without lifting the handset.
Dial [Transfer] [Function] [0] keys during a conversation.
Station No: 2 – 6 digits
N-8000MS/8500MS only
Station No: 2 – 6 digits
Dial during monitoring
Zone No.: 1 – 3 digits
Zone No.: 1 – 3 digits
Function Item Operation Remarks
Automatic call transfer