Dcmdx bit definitions -24 – Intel PXA255 User Manual
Page 174
5-24
Intel® PXA255 Processor Developer’s Manual
DMA Controller
Table 5-12. DCMDx Bit Definitions (Sheet 1 of 2)
0x4000_02xC
DMA Command Register (DCMDx)
DMA Controller
Bit
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
IN
C
S
RC
AD
DR
IN
C
T
RG
AD
DR
FLO
WSR
C
FLO
WTR
G
reserved
S
T
AR
T
IRQ
EN
EN
DI
RQE
N
re
ser
v
e
d
EN
DI
AN
SIZE
WID
T
H
re
ser
v
e
d
LENGTH
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bits
Name
Description
31
INCSRCADDR
Source Address Increment Setting. (read / write).
0 –
Do not increment Source Address
1 – Increment Source Address at the end of each internal bus transaction initiation by
DCMD[SIZE]
If the source address is an internal peripheral’s FIFO address or external IO address, the
address is not incremented on each successive access. In this case, this bit must be 0.
30
INCTRGADDR
Target Address Increment Setting. (read / write).
0 –
Do not increment Target Address
1 – Increment Target Address at the end of each internal bus transaction initiated by
DCMD[SIZE]
If the target address is an internal peripheral’s FIFO address or external IO address, the
address is incremented on each successive access. In this cases the bit must be 0.
29
FLOWSRC
Flow Control by the source. (read / write).
0 –
Start the data transfer immediately.
1 – Wait for a request signal before initiating the data transfer.
Indicates the flow control of the source. This bit must be ‘1’ if the source is an onchip or
external peripheral.
If either the DCMD[FLOWSRC] or DCMD[FLOWTRG] bit is set, the current DMA does not
initiate a transfer until it receives a request. Do not set both the DCMD[FLOWTRG] and
DCMD[FLOWSRC] bit to1.
28
FLOWTRG
Flow Control by the target. (read / write).
0 –
Start the data transfer immediately.
1 – Wait for a request signal before initiating the data transfer.
Indicates the Flow Control of the target. This bit must be ‘1’ if the target is an onchip or
external peripheral.
If either the DCMD[FLOWSRC] or DCMD[FLOWTRG] bit is set, the current DMA does not
initiate a transfer until it receives a request. Do not set both the DCMD[FLOWTRG] and
DCMD[FLOWSRC] bit to 1.
27:23
—
reserved
22
STARTIRQEN
Start Interrupt Enable (read / write), Reserved for the No-Descriptor Fetch Mode
0 –
no interrupt is generated.
1 – Allow interrupt to pass when the descriptor (i.e., 4 words) for the channel are loaded.
Sets DCSR[StartIntr] interrupt for the channel when this descriptor is loaded.
21
ENDIRQEN
End Interrupt Enable (read / write).
0 –
no interrupt is generated.
1 – set DCSR[EndIntr] interrupt for the channel when DCMD[LENGTH] is decreased to
zero.
Indicates that the interrupt is enabled as soon as the data transfer is completed.
20:19
—
reserved