Intel PXA255 - Manual (Page 41)

Intel® PXA255 Processor Developer’s Manual 2-11
System Architecture
nPIOW/
GPIO[51]
ICOCZ
PCMCIA I/O write. (output) Performs write transactions
to PCMCIA I/O space.
Hi-Z - Note [1] Note [5]
nPIOR/
GPIO[50]
ICOCZ
PCMCIA I/O read. (output) Performs read transactions
from PCMCIA I/O space.
Hi-Z - Note [1] Note [5]
nPCE[2]/
GPIO[53]
ICOCZ
PCMCIA card enable 2. (output) Selects a PCMCIA
card. nPCE[2] enables the high byte lane and nPCE[1]
enables the low byte lane.
MMC clock. (output) Clock signal for the MMC
Controller.
Hi-Z - Note [1] Note [5]
nPCE[1]/
GPIO[52]
ICOCZ
PCMCIA card enable 1. (outputs) Selects a PCMCIA
card. nPCE[2] enables the high byte lane and nPCE[1]
enables the low byte lane.
Hi-Z - Note [1] Note [5]
nIOIS16/
GPIO[57]
ICOCZ
IO Select 16. (input) Acknowledge from the PCMCIA
card that the current address is a valid 16 bit wide I/O
address.
Hi-Z - Note [1] Note [5]
nPWAIT/
GPIO[56]
ICOCZ
PCMCIA wait. (input) Driven low by the PCMCIA card to
extend the length of the transfers to/from the PXA255
processor.
Hi-Z - Note [1] Note [5]
PSKTSEL/
GPIO[54]
ICOCZ
PCMCIA socket select. (output) Used by external
steering logic to route control, address, and data signals
to one of the two PCMCIA sockets. When PSKTSEL is
low, socket zero is selected. When PSKTSEL is high,
socket one is selected. Has the same timing as the
address bus.
Hi-Z - Note [1] Note [5]
nPREG/
GPIO[55]
ICOCZ
PCMCIA Register select. (output) Indicates that the
target address on a memory transaction is attribute
space. Has the same timing as the address bus.
Hi-Z - Note [1] Note [5]
LCD Controller Pins
L_DD(7:0)/
GPIO[65:58]
ICOCZ
LCD display data. (outputs) Transfers pixel information
from the LCD Controller to the external LCD panel.
Hi-Z - Note [1] Note [3]
L_DD[8]/
GPIO[66]
ICOCZ
LCD display data. (output) Transfers pixel information
from the LCD Controller to the external LCD panel.
Memory Controller alternate bus master request.
(input) Allows an external device to request the system
bus from the Memory Controller. Hi-Z - Note [1] Note [3]
L_DD[9]/
GPIO[67]
ICOCZ
LCD display data. (output) Transfers pixel information
from the LCD Controller to the external LCD panel.
MMC chip select 0. (output) Chip select 0 for the MMC
Controller.
Hi-Z - Note [1] Note [3]
L_DD[10]/
GPIO[68]
ICOCZ
LCD display data. (output) Transfers pixel information
from the LCD Controller to the external LCD panel.
MMC chip select 1. (output) Chip select 1 for the MMC
Controller.
Hi-Z - Note [1] Note [3]
L_DD[11]/
GPIO[69]
ICOCZ
LCD display data. (output) Transfers pixel information
from the LCD Controller to the external LCD panel.
MMC clock. (output) Clock for the MMC Controller.
Hi-Z - Note [1] Note [3]
L_DD[12]/
GPIO[70]
ICOCZ
LCD display data. (output) Transfers pixel information
from the LCD Controller to the external LCD panel.
RTC clock. (output) Real time clock 1 Hz tick.
Hi-Z - Note [1] Note [3]
Table 2-6. Pin & Signal Descriptions for the PXA255 Processor (Sheet 3 of 9)
Pin Name Type Signal Descriptions Reset State Sleep State