Super Systems SuperDATA - Manual (Page 41)

Super Systems Inc Page 41 of 172 Super Data Operations Manual
*configures connection 8 for Honeywell UDC protocol
*note, Port is set to "none" which keeps this connection disconnected
PROTOCOL="HW-UDC"
PORT = "none"
BAUD = "4800"
DBITS = "7"
PARITY = "EVEN"
SBITS = "1"
{ECON8}
{SINST }
*sample instrument configurations
*MMI_MSI Instruments on Connection 1
*DUALPRO MASTER INSTRUMENT WITH V4 LOGIC PROGRAMS IN THE FOREGROUND
1CH#1(1) = "DUALPRO-V4.0, PROG(1), ACW:E3, ALM(36,0,0,0,0)" = "CH1"
*DUALPRO(GENERIC) SLAVE TABLE 29 BLOCKS 0,1 AND 2
1CH#20(1-29) = "MMIGEN-V4.0, BLK:012,ALM(1,800,2,14,12)" = "CH1_T29"
*DUALPRO(GENERIC) SLAVE TABLE 27 BLOCKS 3,4 AND 5 WITHOUT DATALOGGING
1CH#21(1-27) = "MMIGEN-V4.0, BLK:345, NOLOG" = "1_XXX"
*DUALPRO MASTER INSTRUMENT WITH V3.5 RECIPES IN THE FOREGROUND
1CH#2(2) = "DUALPRO-V4.0, PROG(3), ACW:E3, ALM(36,0,0,0,0)" = "CH2"
*CARB-PC ON BANK 2
1CH#3(17) = "CARB-PC" = "CH4-CPC"
*10PRO, 10PRO-E, 10PRO-L, BC-560
1CH#4(33) = "10PRO" = "CH4-10P"
*10PRO-E OR 10PRO-L IN BLOCK MODE
1CH#5(34) = "MMIGEN-V4.0, BLK:0,ABC:01" = "CH5-10PB"
*V3.0 CARBPRO
1CH#6(49) = "UCARB-V3.0, BC CONT, PROG(3), ALM(36,0,0,0,0)" = "CH6-V3CP"
*V3.0 MULTICARB
1CH#7(50) = "MCARB-V3.0, BC CONT, PROG(3), ALM(36,0,0,0,0)" = "CH7-V3MC"
*V3.0 UNIPRO
1CH#8(51) = "UNIPRO-V3.0, BC CONT, PROG(3), ALM(36,0,0,0,0)" = "CH8-V3UP"
*V3.5 CARBPRO
1CH#9(65) = "UCARB-V3.5, BC CONT, PROG(3), ALM(36,0,0,0,0)" = "CH9-V35CP"
*AACC2000 INSTRUMENT
1CH#10(66) = "MMIGEN-V4.0, BLK:012,ABC:02" = "AACC2"
*Modbus Instruments on connection 2
2CH#16(1)="HWM_GEN,L:1,A:2,T:1,A:4,ASP:4,PG:1,SMULT:2x10,4x0.01" = "HW3300x"
2CH#30(1)="HWM_UDC3300,L:1,A:2,T:1,A:4,ASP:4,PG:1,SMULT:2x10,4x0.01"="HW3300"
2CH#31(2)="HWM_UDC2300,L:1,A:2,T:1,A:4,ASP:4,SMULT:2x10,4x0.01" = "HW2300"
2CH#17(7)="HWM_DPR180,A:8,CV:8,MV:8,SMULT:17x100.0,18x1000,19x100"="DPR180"
2CH#32(3)="HWM_UDC5300,L:1,A:2,T:1,A:4,ASP:4,PG:1,SMULT:2x10"="HW5300"
2CH#33(4)="HWM_VRX,A:8,CV:8,MV:8" = "HWVRX"
2CH#11(12) = "MMI_MOD,MB:0-10" = "MP-MOD2"
2CH#70(5) = "MOD_PMC,MB:0-50,MB:50-25" = "1RB01"
2CH#18(9) = "HWM_DPR3000,IN:8,DIN:2,AB:8" = "DPR3000"
*Honeywell CPL Instruments on Connection 3
3CH#34(102)="CPL_HW,CB:256-6,CB:601-4,SMULT:3x100,4x10)="DCP550"
*Yokogawa CPL Instruments on Connection 4
4CH#40(72)="CPL_YOK,CB:0-10,SMULT:3x100,4x10)="UT750"
*Honeywell UDC Instruments on Connection 5
5CH#35(78)="UDC3000"="UDC3000"
*AllenBradley DF1 Instruments on Connection 6
6CH#81(1-7) = "AB_PLC,DB:0-30,DB:30-10" = "AB-PLC5"
6CH#82(1-9) = "AB_SLC,DB:1-36,DB:50-40" = "SLC-N9"