Verilink WANsuite 6x30 (34-00315.B) Product Manual - Manual (Page 3)

iii
WANsuite 6130 FCC
Requirements The WANsuite 6130 has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harm-
ful interference in which case the user is required to correct the interference at his own expense.
This device must also accept any interference received, including interference that may cause
undesired operation.
WARNING: For use only with a certified Class 2 power supply. See Power Source in
Appendix A, Specifications.
WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
WANsuite 6130
Canadian Emissions
Requirements This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of Commu-
nications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites appli-
cables aux appareils numériques (de la class A) prescrites dans le Règlement sur le brouillage
radioélectrique edicté par le ministère des Communications du Canada.
WANsuite 6130 Safety
Precautions When handling this equipment, follow these basic safety precautions to reduce the risk of elec-
tric shock and injury:
• F o llo w all w arn in g s and instru ctio ns m ark ed o n th e p ro du ct an d in the m anu al.
• U n p lug the h ard w are fro m the w all o u tlet b efo re clean in g. D o n o t use liq uid clean ers o r aerosol clean-
ers. U se a slig htly d am p cloth fo r cleanin g.
• D o n o t p lace th is p ro d uct o n an u nstab le cart, stan d, or table. It m ay fall, cau sin g serio u s d am ag e to
th e p ro du ct.
• S lo ts in th e un it are p ro v id ed for ven tilation to pro tect it from o v erh eatin g . T h ese op en ing s m u st no t
be b lock ed o r co v ered . N ev er p lace this p ro d uct n ear a rad iato r o r h eat reg ister.
• T h is p ro du ct sh o uld b e o perated o nly fro m th e typ e o f po w er so u rce in d icated on th e m arkin g lab el
and m an u al. If y ou are u n su re o f th e ty p e o f po w er su p ply yo u are u sing , con su lt yo u r d ealer or lo cal
po w er co m p any.
• D o n o t allo w an y thin g to rest o n the p o w er co rd . D o n o t lo cate th is p ro d uct w here the co rd in terferes
w ith th e free m ov em en t o f p eo ple.
• D o n ot o verload w all ou tlets an d ex tensio n co rds, as th is can resu lt in fire o r electric sh o ck .
• N ev er p u sh o b jects o f an y k ind into th e u nit. T hey m ay to u ch d an gerou s v o ltag e p o ints o r sh o rt ou t
parts th at co u ld result in fire o r electric sho ck . N ev er sp ill liq u id o f an y k ind o n th is eq u ip m en t.
• U n p lug the eq u ip m ent fro m th e w all ou tlet an d refer serv icin g to q u alified service p erso nn el u nd er th e
fo llo w in g co n d ition s:
• When the power supply cord or plug is damaged or frayed.
• If liquid has been spilled into the product.
• If the product has been exposed to rain or water.
• If the product has been dropped or if the housing has been damaged.