TA Triumph-Adler FAX 950 - Manual (Page 133)

10-15
6HFWLRQ
Options
• Status Overall tab
This tab consists of 3 group boxes: the Information box, the Call for
service box and the Operator call box.
The amount of memory installed in the printer for printing purposes is
displayed in the Information box. If printing troubles develop,
information regarding the trouble is indicated by check marks in the
Call for service and Operator call boxes. The information presented
in these two boxes will indicate whether you can resolve the trouble
yourself or that it is necessary to call for service.
If there is a check mark next to any of the error items listed in the Call
for service box, contact your service representative, an authorised
service centre or the place of purchase.
● Errors which can be resolved by the operator
Troubles which are indicated by a checked mark in the Operator call
box can be resolved as follows.
• Paper JAM
Paper has jammed in the printer. Follow the procedure in “Paper has
Jammed”, page 6-4, and remove the jammed paper.
• Paper Empty
There is no paper in the paper cassette. Set paper in the paper
cassette. Refer to “(3) Setting Paper”, on page 2-6.
• Cover open
The printer is open. Close it securely.
• Power off or cable problem
The power cord is not connected correctly to the printer or the parallel
cable is not attached to the printer and computer ports securely.
Connect the power cord and/or the parallel cable correctly.
• System error (Over run)
The printer cannot handle the amount of data being sent by the
computer. Change the printing resolution setting to 300 dpi x 300 dpi.
If this error persists, contact your service representative, an
authorised service centre or the place of purchase.
• Communication Error
An error has occurred in communication between the printer and the
computer. Make sure the parallel cable is attached to both ports securely.
If communication errors persist, replace the cable.
• Toner Empty
There is insufficient toner in the printer. Follow the procedure in
“Replacing the Toner Cartridge”, page 5-2, and replace the toner
cartridge.
• Toner Cartridge Empty or Missing
The toner cartridge, or the imaging unit, is not installed properly.
Refer to “Replacing the Toner Cartridge”, page 5-2, or “Replacing the
Imaging Unit”, page 5-4, and confirm that both the toner cartridge and
the imaging unit are set properly.
• Paper Mismatch
The size of paper loaded in the paper cassette is different from the
paper size setting, paper was fed into the printer at a skewed angle,
or two or more overlapping pieces of paper were fed into the printer.
Refer to “
4 Print out is accomplished on the wrong size paper”, page
6-6, and confirm the correct paper size.
• Upper Cassette Empty
The paper cassette is not set properly in the printer. Refer to
“(3) Setting Paper”, page 2-6, and set the paper cassette properly.
• Duplex Unit Empty
The Duplex unit is not installed properly. Install the Duplex unit
properly.
3 Print Manager window
Print Manager is a program which manages printing operations. The
Print Manager window displays information about the file currently
being printed as well as those files queued for printing. Printing can
also be paused, resumed or cancelled from within Print Manager.
4 Cancelling printing
1. In the Print Manager window, highlight the print job you want to
cancel by clicking on the corresponding file name.
2. Click on Pause and then Delete. The selected file name will be
deleted from the printing queue.
5 Pausing and resuming printing
1. In the Print Manager window, highlight the print job you want to
pause by clicking on the corresponding file name.
2. Click on Pause. Printing will stop.
3. Click on Resume to resume printing.
(8) Removing the Printer Driver
Even if you no longer plan to use this printer with your computer, it is
usually not necessary to remove the files related to this printing
system. If, however, for any reason it becomes necessary to remove
these files from your computer, carry out the following procedure.
1. Start up Windows NT 4.0. Quit all other applications that may be
open.
2. Click on Start in the Task Bar. Use the mouse to point to Settings
and click on Printers in the submenu which is displayed.
3. The Printers folder will open. Use the right mouse button to click
on the icon for this printer.
4. Click on Delete.
5. Click on Yes.
6. The files for this Printing System will be removed.
* If this printer was selected as the default printer, a message
asking you to select a new default printer will be displayed.