Teledyne 9110TH - Nitrogen Oxides Analyzer - Manual (Page 17)

Table of Contents Model 9110TH NOx Analyzer
Teledyne Analytical Instruments xvii
Figure 3-19: 9110TH – Internal Pneumatics with Ambient Zero-Span Valve Option 50A ............................... 32
Figure 3-20: 9110TM – Internal Pneumatics with Ambient Zero-Span Valve Option 50A ............................... 33
Figure 3-21: 9110TH - Internal Pneumatics for Zero Scrubber/Dual Pressurized Span, Option 50D ............. 37
Figure 3-22: 9110TM - Internal Pneumatics for Zero Scrubber/Dual Pressurized Span, Option 50D ............. 38
Figure 3-23: 9110TH – Internal Pneumatics with O2 Sensor Option 65A ....................................................... 39
Figure 3-24: 9110TM – Internal Pneumatics with O
2
Sensor Option 65A ........................................................ 40
Figure 3-23: O
2
Sensor Calibration Set Up ...................................................................................................... 48
Figure 4-1: Front Panel Display with “SAMPLE” Indicated in the Mode Field ............................................... 53
Figure 4-2: Viewing 9110TH/M TEST Functions ............................................................................................ 56
Figure 4-3: Viewing and Clearing 9110TH/M WARNING Messages ............................................................. 57
Figure 4-4: APICOM Graphical User Interface for Configuring the DAS ....................................................... 79
Figure 4-5: Default Pin Assignments for Rear Panel com Port Connectors (RS-232 DCE & DTE) .............. 92
Figure 4-6: CPU COM1 & COM2 Connector Pin-Outs in RS-232 mode. ...................................................... 93
Figure 4-7: COM – LAN / Internet Manual Configuration ............................................................................... 98
Figure 4-8: Jumper and Cables for Multidrop Mode.....................................................................................103
Figure 4-9: RS-232-Multidrop Host-to-Analyzer Interconnect Diagram .......................................................104
Figure 4-10: Analog Output Connector Key ...................................................................................................114
Figure 4-11: Setup for Calibrating Analog Outputs ........................................................................................134
Figure 4-12: Setup for Calibrating Current Outputs .......................................................................................136
Figure 4-13: Alternative Setup for Calibrating Current Outputs .....................................................................136
Figure 4-14. DIAG – Analog Inputs (Option) Configuration Menu .................................................................139
Figure 4-15: Status Output Connector ...........................................................................................................149
Figure 4-16: Control Inputs with local 5 V power supply ................................................................................151
Figure 4-17: Control Inputs with external 5 V power supply ..........................................................................151
Figure 4-18: APICOM Remote Control Program Interface ............................................................................158
Figure 5-1: Gas Supply Setup for Determination of NO
2
Conversion Efficiency ..........................................169
Figure 5-2: Pneumatic Connections–With Zero/Span Valve Option (50A) ..................................................173
Figure 5-3: Pneumatic Connections–With 2-Span point Option (50D) –Using Bottled Span Gas ...............174
Figure 5-4: Pneumatic Connections–With Zero/Span Valve Option (50) ....................................................178
Figure 6-1: Sample Particulate Filter Assembly ...........................................................................................192
Figure 6-2: Particle Filter on O
3
Supply Air Dryer ........................................................................................193
Figure 6-3: NO
2
Converter Assembly ...........................................................................................................195
Figure 6-4: Reaction Cell Assembly .............................................................................................................197
Figure 6-5: Critical Flow Orifice Assembly ...................................................................................................198
Figure 7-1: Viewing and Clearing Warning Messages .................................................................................204
Figure 7-2: Switching Signal I/O Functions ..................................................................................................206
Figure 7-3: Motherboard Watchdog Status Indicator ...................................................................................207
Figure 7-4: Relay Board PCA .......................................................................................................................208
Figure 7-5: 9110TH – Basic Internal Gas Flow ............................................................................................211
Figure 7-6: 9110TH – Internal Gas Flow with Ambient Zero Span, OPT 50A .............................................212
Figure 7-7: 9110TH – Internal Gas Flow with O
2
Sensor, OPT 65A ............................................................213
Figure 7-8: 9110TM – Basic Internal Gas Flow ............................................................................................214
Figure 7-9: 9110TM – Internal Gas Flow with Ambient Zero Span, OPT 50A .............................................215
Figure 7-10: 9110TM – Internal Gas Flow with O
2
Sensor, OPT 65A ...........................................................216
Figure 7-11: Location of AC power Configuration Jumpers ...........................................................................228
Figure 7-12: Pump AC Power Jumpers (JP7) ................................................................................................230
Figure 7-13: Typical Set Up of AC Heater Jumper Set (JP2) ........................................................................231
Figure 7-14: Typical Set Up of AC Heater Jumper Set (JP6) ........................................................................232
Figure 7-15: Typical Set Up of Status Output Test ........................................................................................236
Figure 7-16: Pressure / Flow Sensor Assembly .............................................................................................241
Figure 7-17: Pre-Amplifier Board Layout ........................................................................................................248
Figure 7-18: 9110TH/M Sensor Assembly .....................................................................................................250
Figure 7-19. 3-Port Reaction Cell Oriented to the Sensor Housing ...............................................................250
Figure 7-20: Relay PCA with AC Relay Retainer In Place .............................................................................252
Figure 7-21: Relay PCA Mounting Screw Locations .....................................................................................252
Figure 8-1: 9110TH/M Sensitivity Spectrum ................................................................................................257
Figure 8-2: NO
2
Conversion Principle ..........................................................................................................258
Figure 8-3: Reaction Cell with PMT Tube ....................................................................................................259