FEC FUSIONE-HS-2 - Manual (Page 133)

FUSION Operations Manual Chapter 7: System Operations (Rev.2)
Page 7-9
7.2.5 Parameter Data List & Explanation
ITEM DATA SETTING WORK D- No DATA
System
0 00 TORQUE UNIT #. 0: Nm
0 01 ROM VERSION (Not adjustable) 1: Kg.m
0 02 AMPLIFIER VERSION (Not adjustable) 2: Kgcm
0 03 FASTENING FUNCTION VERSION (1.03 for FEC) See Pg 7-12 3: Ft lb
0 04 External gear ratio 0.3 ~ 3.00
0 05 Gear Head Type See Pg 7-13
Tool Data
(This section is
factory set and
cannot be
changed)
0 10 TOOL # (not adjustable) 4: in lb
0 11 TOOL CAL TORQUE.
0 12 CAL. VOLTAGE
0 13 ZERO TORQUE VOLTAGE
0 14 PULSES PER DEGREE
0 15 MOTOR TYPE
0 16 TRANSMISSION RATIO
0 17 ROTATE CW=0 / CCW=1
0 18 CCW TQ. CAL. VOLTAGE
0 19 TOOL SERIAL # (1ST 4 DIGITS)
0 1A TOOL SERIAL # (2ND 4 DIGITS)
0 1b Tool Cycle count Upper 4 digit
0 1c Tool Cycle count Lower 4 digit
Tool type 0 20 TOOL # See List on next pages
Tool Info
0 21 Start switch trigger level 10 Change to 100 to disable
0 22 Start switch High Speed level 40 Change to 100 to disable
0 23 CW/CCW switch trigger level 20 Change to 100 to disable
0 24 Switch setup (Factory setup) 67
0 25 Switch setup (Factory setup) 30
0 26 Switch setup (Factory setup) 1
0 27 Switch setup (Factory setup) 200
0 28 Switch setup (Factory setup) 5
0 29 Switch setup (Factory setup) 80
Real Time Clock
(After ver. 2.20)
0 30 Year – ‘yyyy” example ‘2007’ See 7.5 for detail
0 31 Month & Date ‘mmdd example ‘0131’ = Jan. 31
0 32 Hour & Minute ‘hhmm’ example ‘1759 = 17:59
0 33 Seconds ‘00ss’ example ‘0020’ = 20 seconds
RS232 Format 0 40 - 49 RS232 data alternate communication format See 4.8.4 for set-up
Torque
1~16 00 FASTENING MODE (METHOD + STEPS) See List on next pages
1~16 05 OPTION 1-Future use
1~16 06 OPTION 2-Future use
1~16 10 FULL SCALE TORQUE (CAL TORQUE) +/- 20%
1~16 11 PEAK TORQUE LOW LIMIT
1~16 12 PEAK TORQUE HIGH LIMIT Max. Full Scale x 1.1
1~16 13 STANDARD (STD) TORQUE
1~16 14 SPEED CHANGE TORQUE
1~16 15 1ST TORQUE
1~16 16 SNUG TORQUE
1~16 17 THRESHOLD (THR) TORQUE
1~16 18 CROSSOVER (CROS) TORQUE
1~16 19 TORQUE INHIBIT LIMIT Max. Full Scale x 1.1
1~16 1A Not Used
1~16 1B BREAKAWAY TORQUE LIMIT Max. Full Scale x 1.1
1~16 1C FINAL TORQUE LOW LIMIT
1~16 1D FINAL TORQUE HIGH LIMIT Max. Full Scale x 1.1
1~16 1E 2ND RATE START TORQUE Max. Full Scale x 1.1
Angle
1~16 20 ANGLE LOW LIMIT
1~16 21 ANGLE HIGH LIMIT Max. 9999 deg
1~16 22 STANDARD (STD) ANGLE Max. 9999 deg
1~16 23 1ST ANGLE Max. 9999 deg
1~16 24 CROSSOVER ANGLE Max. 9999 deg
1~16 25 ANGLE CORRECTION 0-99 deg.
1~16 26 Future use
1~16 27 Future use
Rate
1~16 30 1ST TORQUE RATE LOW LIMIT For all Rate settings
Max. “5000”
Setting “0000” in any of
The LOW rate settings
disables low rate judgment
1~16 31 1ST TORQUE RATE HIGH LIMIT
1~16 32 2ND TORQUE RATE LOW LIMIT
1~16 33 2ND TORQUE RATE HIGH LIMIT
1~16 34 3RD TORQUE RATE HIGH LIMIT
1~16 35 3RD TORQUE RATE HIGH LIMIT
(Continued on next page)