FEC FUSIONE-HS-2 - Manual (Page 153)

FUSION Operations Manual
7.3.5 Data Edit mode operation.
FIG. 7-3-3 Setup mode operation
When the Torque Unit number (PARM 0 D
changed, the [DATA] display will show "CHNG," and the D
the vertical arrow buttons to choose YES or NO; YES means that the data will be entered if
the confirmation SET button is pressed. The [SET] and [MODE] buttons
when "NO" appears. If no button is pushed within five seconds, the new data will be ignored,
and the system will exit the Data Edit mode.
Note:
When the Torque Unit (PARM 0, and D
is changed, all torque settings (D
cleared.
FUSION Operations Manual Chapter 7: System Operations (Rev.2)
Page 7-29
Data Edit mode operation.
Depressing the [MODE] button will bring up the
mary setup mode. The blinking cursor
tioned in the right most digit in the
field and depressing it again will bring it to the l
of the field. Use the [ ↓↓↓↓ ] and [ ↑↑↑↑ ] buttons to select the
desired [COUNT/D-NO] number which is to be edited.
After you have selected the Parameter number and
the Data number you would like to edit, press the
[SET] button to enter the Data Edit mode. The blin
ing digit will now appear at the left digit of the DATA
field. You can move one digit to the right each time
you press the [MODE] button. By pressing the button
four times, you leave the Data Edit mode and return
to the Setup mode (without saving any changes).
Use the [ ↓↓↓↓ ] and [ ↑↑↑↑ ] buttons to increase or decrease
the digit that is blinking.
After changes have been made, pressing the [SET]
button will save the changes and exit to the Setup
mode.
If the entered values are out of range / limits, "
appear, and the new data will be ignored. In this
case, return to the parameter number selection (using
the [MODE] key) and enter data that is acceptable.
3 Setup mode operation
When the Torque Unit number (PARM 0 D-NO 00) or the Tool Type (PARM 0 D
changed, the [DATA] display will show "CHNG," and the D-NO display will show "NO." Use
the vertical arrow buttons to choose YES or NO; YES means that the data will be entered if
the confirmation SET button is pressed. The [SET] and [MODE] buttons
when "NO" appears. If no button is pushed within five seconds, the new data will be ignored,
and the system will exit the Data Edit mode.
When the Torque Unit (PARM 0, and D-NO 00) or the Tool Type (PARM 0, and D
ged, all torque settings (D-No 00-1E) and speed settings (D-
7: System Operations (Rev.2)
Depressing the [MODE] button will bring up the pri-
he blinking cursor will be posi-
digit in the [COUNT/D-NO]
field and depressing it again will bring it to the left digit
] buttons to select the
number which is to be edited.
rameter number and
the Data number you would like to edit, press the
[SET] button to enter the Data Edit mode. The blink-
ing digit will now appear at the left digit of the DATA
field. You can move one digit to the right each time
on. By pressing the button
four times, you leave the Data Edit mode and return
to the Setup mode (without saving any changes).
] buttons to increase or decrease
After changes have been made, pressing the [SET]
button will save the changes and exit to the Setup
If the entered values are out of range / limits, " Err " will
ew data will be ignored. In this
case, return to the parameter number selection (using
the [MODE] key) and enter data that is acceptable.
NO 00) or the Tool Type (PARM 0 D-NO 20) is
NO display will show "NO." Use
the vertical arrow buttons to choose YES or NO; YES means that the data will be entered if
the confirmation SET button is pressed. The [SET] and [MODE] buttons will have no effect
when "NO" appears. If no button is pushed within five seconds, the new data will be ignored,
NO 00) or the Tool Type (PARM 0, and D-No 20)
-No 50-56) will be