Sfp+ 10g sonet/sdh and otn optical interfaces, Specifications, 10g sonet/sdh and otn optical interfaces – EXFO FTB-800 Series for FTB-1 User Manual
Page 519: Netblazer
Specifications
NetBlazer
509
SFP+ 10G SONET/SDH and OTN Optical Interfaces
SFP+ 10G SONET/SDH and OTN Optical
Interfaces
SFP+
c
10G SONET/SDH AND OTN OPTICAL INTERFACES
Transceiver type
OC-192/STM-64/OTU2
OC-192/STM-64/OTU2
OC-192/STM-64/OTU2
Wavelength (nm)
1310
1550
1550
Model
FTB-8693
FTB-8694
FTB-8695
Tx level (dBm)
–6 to –1
–1 to 2
0 to 4
Rx level sensitivity (dBm)
–11 to 0.5
–14 to –1
–24 to –7
Maximum reach
10 km
40 km
80 km
Transmission bit rate (Gbit/s)
9.9532 ± 4.6 ppm
10.7092 ± 4.6 ppm (OTU2)
11.0491 ± 4.6 ppm (OTU1e)
11.0957 ± 4.6 ppm (OTU2e)
11.2701 ± 4.6 ppm (OTU1f)
11.3176 ± 4.6 ppm (OTU2f)
9.9532 ± 4.6 ppm
10.7092 ± 4.6 ppm (OTU2)
11.0491 ± 4.6 ppm (OTU1e)
11.0957 ± 4.6 ppm (OTU2e)
11.2701 ± 4.6 ppm (OTU1f)
11.3176 ± 4.6 ppm (OTU2f)
9.9532 ± 4.6 ppm
10.7092 ± 4.6 ppm (OTU2)
11.0491 ± 4.6 ppm (OTU1e)
11.0957 ± 4.6 ppm (OTU2e)
11.2701 ± 4.6 ppm (OTU1f)
11.3176 ± 4.6 ppm (OTU2f)
Frequency offset generation (ppm)
±50
±50
±50
Reception bit rate (Gbit/s)
9.9532 ± 100 ppm
10.7092 ± 100 ppm (OTU2)
11.0491 ± 120 ppm (OTU1e)
11.0957 ± 120 ppm (OTU2e)
11.2701 ± 120 ppm (OTU1f)
11.3176 ± 120 ppm (OTU2f)
9.9532 ± 100 ppm
10.7092 ± 100 ppm (OTU2)
11.0491 ± 120 ppm (OTU1e)
11.0957 ± 120 ppm (OTU2e)
11.2701 ± 120 ppm (OTU1f)
11.3176 ± 120 ppm (OTU2f)
9.9532 ± 100 ppm
10.7092 ± 100 ppm (OTU2)
11.0491 ± 120 ppm (OTU1e)
11.0957 ± 120 ppm (OTU2e)
11.2701 ± 120 ppm (OTU1f)
11.3176 ± 120 ppm (OTU2f)
Tx operational wavelength range (nm)
1260 to 1355
1530 to 1565
1530 to 1565
Measurement accuracy (uncertainty)
Frequency (ppm)
Optical power (dB)
±4.6
±2
±4.6
±2
±4.6
±2
Maximum Rx before damage (dBm)
a
5
5
3
Jitter compliance
GR-253 (SONET)
G.825 (SDH)
G.8251 (OTN)
GR-253 (SONET)
G.825 (SDH)
G.8251 (OTN)
GR-253 (SONET)
G.825 (SDH)
G.8251 (OTN)
Laser product
Class 1
Class 1
Class 1
Connector
b
LC
LC
LC
Notes
a. To avoid exceeding the maximum receiver power level before damage, an attenuator must be used.
b. External adaptors can be used for other types of connectors.
c.
SFP+ compliance: The FTB-700G Series selected SFP+ shall meet the requirements stated in the SFP-8431 “Enhanced Small Form-Factor Pluggable Module SFP+” Transceiver Multisource Agreemen
(MSA).” The FTB-700G Series selected SFP+ shall meet the requirements stated in the “Specification for Diagnostic Monitoring Interface for Optical Xcvrs.”