Lenze Engineer v2.21 User Manual
Engineer, Ä.pe8ä
Advertising
Table of contents
Document Outline
- Engineer
- Contents
- 1 About this documentation
- 2 Safety instructions
- 3 User interface
- 4 Getting started: creating a project
- 5 Mapping the system structure in the »Engineer« project
- 5.1 Modularising with system modules and axes
- 5.2 Inserting components
- 5.3 Inserting a gearbox
- 5.4 Inserting a device detected online
- 5.5 Insert from referential project
- 5.6 Replace component
- 5.7 Documentation - Add project details
- 5.8 Protecting safe parameters - project-related password entry
- 6 Establishing an online connection
- 6.1 Build project
- 6.2 Going online
- 6.2.1 Setting the communication path
- 6.2.1.1 Diagnostic adapter
- 6.2.1.2 CAN
- 6.2.1.3 Ethernet / Ethernet IPC
- 6.2.1.4 PROFIBUS
- 6.2.1.5 PROFINET
- 6.2.1.6 Gateway controller -> CAN
- 6.2.1.7 Gateway controller -> EtherCAT
- 6.2.1.8 Gateway Controller -> EtherCAT ADS (Beckhoff)
- 6.2.1.9 Gateway Siemens - STEP 7 Communication Server (available by call in STEP 7)
- 6.2.2 Checking the serial number
- 6.2.1 Setting the communication path
- 6.3 Going offline
- 6.4 System bus configurator
- 6.5 PROFINET address configurator
- 6.6 EtherNet / IP addresses configurator
- 7 Device functions with active online connection
- 7.1 Options
- 7.2 Controlling an inverter: Enable/inhibit, start stop application
- 7.3 Application and parameter set transfer
- 7.4 Optical tracking - device identification within the machine
- 7.5 Manual control of the motor direction of rotation: Rotating the axes manually
- 7.6 Diagnostics
- 7.7 Data logger
- 7.7.1 User interface
- 7.7.2 Operation
- 7.7.2.1 Selecting the variables to be recorded
- 7.7.2.2 Defining the recording time/sampling rate
- 7.7.2.3 Defining the trigger condition
- 7.7.2.4 Using the time axis
- 7.7.2.5 Starting/stopping recording
- 7.7.2.6 Adjusting the representation
- 7.7.2.7 Reading individual measured values
- 7.7.2.8 Comparing peak values
- 7.7.3 Data records
- 7.8 Oscilloscope
- 8 Defining the system functionality
- 8.1 Representation in the project view
- 8.2 Terminology used
- 8.3 General notes with regard to the procedure
- 8.4 Parameterising & configuring the devices
- 8.5 Assigning an application to the device
- 8.6 Parameter setting in the »Engineer«
- 8.7 Copying parameter sets
- 8.8 Configuring the terminal assignment
- 8.9 Parameterising the application
- 8.10 Function block editor (FB Editor)
- 8.11 Port editor (ports)
- 8.12 User menu
- 8.13 Inserting & configuring a machine application
- 8.14 Creating an interconnection via the electrical shaft
- 9 Inserting & configuring a network
- 10 Application examples
- 11 Catalogue management in the »Engineer«
- 12 Error messages
- 13 Menu reference - Overview of the menu commands
- 14 Appendix
- 14.1 Export data
- 14.2 Managing cam data with the »Cam Manager«
- 14.3 Creating cam data with the »Cam Editor«
- 14.4 User motors
- 14.4.1 Creating user motors from controller settings
- 14.4.2 Saving a user motor to the user motor catalogue
- 14.4.3 Inserting the user motor into the project
- 14.4.4 Modifying/supplementing motor default values
- 14.4.5 Transferring default values to the controller
- 14.4.6 Deleting/exporting/importing user motors
- 15 Glossary
- Index
- Your opinion is important to us