Rockwell Automation 1771-QDC, D17716.5.93(Passport) PLASTIC MOLDING MODULE - Manual (Page 79)

Select Command and Status Bits to
Sequence Machine Operation
Chapter 6
6-3
Table 6.C
Status and Command Bit Interaction for Profile Execution
For this
Profile/Movement:
During Execution
this bit in B34 is:
At Completion
this bit in B34 is:
At completion
If this Then this
command bit is: status bit is:
SET RESET SET RESET also SET also SET
1st Clamp Close SYS21ĆB00 SYS02ĆB00 SYS02ĆB00 SYS21ĆB00 CPC03ĆB08 SYS22ĆB00
2nd Clamp Close SYS21ĆB01 SYS02ĆB01 SYS02ĆB01 SYS21ĆB01 CPC03ĆB09 SYS22ĆB01
3rd Clamp Close SYS21ĆB02 SYS02ĆB02 SYS02ĆB02 SYS21ĆB02 CPC03ĆB10 SYS22ĆB02
Low Pressure Close SYS21ĆB03 SYS02ĆB03 SYS02ĆB03 SYS21ĆB03 --- SYS22ĆB03
Injection SYS21ĆB04 SYS02ĆB04 SYS02ĆB04 SYS21ĆB04 --- ---
Pack SYS21ĆB05 SYS02ĆB05 SYS02ĆB05 SYS21ĆB05 --- ---
Hold SYS21ĆB06 SYS02ĆB06 SYS02ĆB06 SYS21ĆB06 HPC03ĆB08 SYS22ĆB06
PreĆdecompression SYS21ĆB07 SYS02ĆB07 SYS02ĆB07 SYS21ĆB07 HPC03ĆB09 SYS22ĆB07
Plastication SYS21ĆB08 SYS02ĆB08 SYS02ĆB08 SYS21ĆB08 PPC03ĆB08 SYS22ĆB08
PostĆdecompression SYS21ĆB09 SYS02ĆB09 SYS02ĆB09 SYS21ĆB09 --- SYS22ĆB09
1st Clamp Open SYS21ĆB10 SYS02ĆB10 SYS02ĆB10 SYS21ĆB10 OPC03ĆB08 SYS22ĆB10
2nd Clamp Open SYS21ĆB11 SYS02ĆB11 SYS02ĆB11 SYS21ĆB11 OPC03ĆB09 SYS22ĆB11
3rd Clamp Open SYS21ĆB12 SYS02ĆB12 SYS02ĆB12 SYS21ĆB12 OPC03ĆB10 SYS22ĆB12
Clamp Open Slow SYS21ĆB13 SYS02ĆB13 SYS02ĆB13 SYS21ĆB13 --- SYS22ĆB13
Ejector Advance SYS21ĆB14 SYS02ĆB14 SYS21ĆB14 SYS02ĆB14 EPC03ĆB12 SYS22ĆB14
Ejector Retract
(tip strokes)
SYS21ĆB14 SYS02ĆB14 SYS21ĆB14 SYS02ĆB14 EPC03ĆB12 SYS22ĆB15
Final Ejector Retract SYS21ĆB14 SYS02ĆB14 SYS02ĆB14 SYS21ĆB14 --- SYS22ĆB15
where:
These Bits: Report These Functions: or Command These Functions:
SYS21ĆB00 thru B14 profile in progress
SYS02ĆB00 thru B14 profile complete
SYS22ĆB00 thru B03 and B06 thru B15 executing endĆofĆprofile %Ćoutputs
CPC03/HPC03/PPC03/OPC03/EPC03
Bits B08, 09, 10, 12
interrupt movement between profiles
(see tables 6.B and 6.D)