Rockwell Automation 7000 PowerFlex Medium Voltage AC Drive (B Frame) - Classic Control - Manual (Page 380)

6-90 Component Definition and Maintenance
7000-UM150I-EN-P – June 2013 7000 “B” Frame
The following table illustrates the most commonly used test points.
New SCB Board
(80190-378-xx)
Old SCB Board
(80190-278-xx)
Description
TP # Label TP # Label
3 VBCXFR_OUT 1 VBCXFR_OUT Voltage BC on Line Side of Bypass Contactor, unfiltered
4 VABXFR_OUT 2 VABXFR_OUT Voltage AB on Line Side of Bypass contactor, unfiltered
5 VAB2_OUT 3 VAB2_OUT Voltage AB on Slave 1 input winding, unfiltered
6 VBC2_OUT 4 VBC2_OUT Voltage BC on Slave 1 input winding, unfiltered
7 VCA2_OUT 5 VCA2_OUT Voltage CA on Slave 1 input winding, unfiltered
8 VAB3_OUT 6 VAB3_OUT Voltage AB on Slave 2 input winding, unfiltered
9 VBC3_OUT 7 VBC3_OUT Voltage BC on Slave 2 input winding, unfiltered
10 VCA3_OUT 8 VCA3_OUT Voltage CA on Slave 2 input winding, unfiltered
11 VAB1_OUT 9 VAB1_OUT Voltage AB on Master input winding (SCBL) or Motor (SCMB), unfiltered
12 VBC1_OUT 10 VBC1_OUT Voltage BC on Master input winding (SCBL) or Motor (SCBM), unfiltered
13 VCA1_OUT 11 VCA1_OUT Voltage CA on Master input winding (SCBL) or Motor (SCBM), unfiltered
14 VDC_AVG 12 VDC_AVG DC Link Average Voltage across Inverter Side (SCBL only), calculated
28 -15V 24 -15V -15V DC Analog Power
29 AGND 25 AGND Analog Power Common
30 +15V 26 +15V +15V DC Analog Power
31 -24V 27 -24V -24V DC Hall-Effect Transducer Power
32 LEMGND 28 LEMGND Hall-Effect Transducer Power Common
33 +24V 29 +24V +24V DC Hall-Effect Transducer Power
34 +5V 30 +5V +5V DC Digital Power
35 DGND 31 DGND Digital Power Common
36 VN 32 VN Voltage from Filter Capacitor Neutral Point, unfiltered
38 VNG 35 VNG Converter Neutral-Ground Voltage, calculated
64 IDCP 42 IDCP DC Link Current Feedback, filtered
66 IFIELD 45 IFIELD Synchronous Motor Field Current Feedback, filtered
74 DAC_TP1 76 DAC_TP1 Assignable Test Point (Rect_TP1 [SCBL] or INV_TP1 [SCMB] parameters)
75 DAC_TP1 77 DAC_TP1 Assignable Test Point (Rect_TP2 [SCBL] or INV_TP2 [SCMB] parameters)
1 IA1_OUT N/A Across R17 Current Phase A, Master Bridge, unfiltered 
2 IC1_OUT N/A Across R29 Current Phase C, Master Bridge, unfiltered 
15 IA2_OUT N/A Across R33 Current Phase A, Slave 1 Bridge, unfiltered 
27 IC2_OUT N/A Across R66 Current Phase C, Slave 1 Bridge, unfiltered 
40 IA3_OUT N/A Across R75 Current Phase A, Slave 2 Bridge (SCBL) or Motor (SCBM), unfiltered 
41 IC3_OUT N/A Across R89 Current Phase C, Slave 2 Bridge (SCBL) or Motor (SCBM), unfiltered 
62 IDCP_OUT N/A Across R138 DC Link Feedback Current (SCBL), unfiltered
70 IGND_OUT N/A Across R140 Zero Sequence Feedback Current (SCBL), unfiltered
75 IFIELD_OUT N/A Across R156 Field Current Feedback (SCBL), unfiltered
67 DOUT0 63 DOUT0 Digital Output command for DI Contactor (SCBL) or Bypass Contactor (SCBM)
65 DOUT1 62 DOUT1 Digital Output Command for Bypass Enable (SCBM)
60 DOUT3 69 DOUT3 Digital Output Command for DO Contactor (SCBL) or OP Contactor (SCBM)
55 DIN0 N/A Digital Input Status for DI Contactor (SCBL) or Bypass Ctctr (SCBM)
53 DIN1 N/A Digital Input Status for DI Isolation Switch (SCBL) or Bypass Isol. Sw. (SCBM)
50 DIN2 N/A Digital Input Status for OP Contactor (SCBL) or OP Contactor (SCBM)
47 DIN3 N/A Digital Input Status for OP Isolation Switch (SCBL) or OP Isol. Sw. (SCBM)
44 ENCA N/A Pulse Train from the Input of the Encoder Signal, Channel A
45 ENCB N/A Pulse Train from the Input of the Encoder Signal, Channel B
 Requires the usage of isolated probes or isolation channels on the oscilloscope to avoid damaging the PF7000 Drive.
Customer Interface Board
(cont.)