Rockwell Automation GV3000/SE AC Gen. Purpose and Vector Drive Software Start-Up and Ref. Manual - Manual (Page 227)

Index Index-1
I
NDEX
A
AC Line Volts (H.021), 4-67
AC Line Volts (U.018), 4-79
Accel Time 1 (RAMP 1) (P.001), 4-7
Accel Time 2 (RAMP 2) (P.017), 4-25
Alarm codes, 5-1, 5-2
Analog input,
see Input, Analog
Analog output, see Output, Analog
Assistance, technical, VII
AUTO/MAN Key Disable (P.052), 4-42
AutoMax Network Option board, 4-7, 4-48, 4-49,
4-50, 4-51, 4-68
Avoidance Frequency Band 1 (H.011), 4-62
Avoidance Frequency Band 2 (H.013), 4-62
Avoidance Frequency Band 3 (H.013), 4-62
Avoidance Frequency Enable (H.009), 4-60
Avoidance Frequency Midpoint 1 (H.010), 4-61
Avoidance Frequency Midpoint 2 (H.012), 4-61
Avoidance Frequency Midpoint 3 (H.014), 4-61
B
Block diagrams, H-3 to H-8
Braking,
see DC Braking
C
Carrier Frequency (kHz) (P.047), 4-39
Closed-loop control,
see Vector Regulation
Control and Configuration Software, 1-24, 2-37, 4-6
Control Source (P.000), 4-6
ControlNet Network Option board, 4-7, 4-48, 4-49,
4-50, 4-51
Country Defaults (P.049), 4-40
CS3000, see Control and Configuration Software
Current Compounding Gain (U.026), 4-83
Current Limit (P.005), 4-10
D
DC Braking Current (H.007), 4-59
DC Braking Enable (H.005), 4-58
DC Braking Start Frequency (H.006), 4-59
DC Braking Time (H.008), 4-60
Decel Time 1 (RAMP 1) (P.002), 4-8
Decel Time 2 (RAMP 2) (P.018), 4-25
Default parameter settings, E-1 to E-4
DeviceNet Network Option board, 4-7, 4-48, 4-49,
4-50
Diagnostics Display (P.091), 4-53
Diagnostics Source (P.090), 4-53
Digital input, see Input, Digital
Display
description, 3-4
scaling, see Speed Display Scaling (P.028)
Draw Gain Percentage (P.016), 4-24
Drive control, using the keypad for, 3-4
Drive faults,
see Fault Codes
Drive hardware, VII
Drive regulation, overview of, H-1 to H-8
Drive status LEDs, 3-8
E
Elapsed Time Meter (P.029), 4-33
Elapsed Time Meter Reset (P.030), 4-33
Encoder Loss Enable (P.039), 4-35
Encoder PPR (U.001), 4-69
Error codes,
see Alarm Codes, Fault Codes, Error
Log
Error log, 5-1, 5-6 to 5-8
F
Fast flux up feature, 4-80
Fault Auto Reset Attempts (P.043), 4-37
Fault Auto Reset Time (P.044), 4-38
Fault codes, 5-1, 5-3 to 5-6
fatal, 5-9
see also Error Log
Field Weakening Start RPM (U.016), 4-77
First Menu parameters, 4-6 to 4-10
Flux Current Regulator Integral Gain (U.020), 4-79
Flux Current Regulator Proportional Gain
(U.019), 4-79
Flux vector control, 4-1, 4-35, 4-40, H-1
Forward/Reverse Configuration (P.027), 4-31
Function Loss Response (P.026), 4-30
FVC, see Flux Vector Control