Rockwell Automation GV3000/SE AC Gen. Purpose and Vector Drive Software Start-Up and Ref. Manual - Manual (Page 230)

Index-4 GV3000/SE AC Drive Software Reference, Version 6.06
Second Menu parameters, 4-11 to 4-90
Second Menu Password (P.006), 4-10
Second Menu password, entering, 4-11 to 4-13
Sensorless vector control, 4-40, 4-69, H-1
Slip Compensation (H.004), 4-57
Snubber Resistor Kit,
see Input Power/Snubber
Configuration (H.017)
Software Version Number (P.098), 4-54
Speed Display Scaling (P.028), 4-31
Speed loop, description of, H-1
Speed reference, 4-6 to 4-7
displaying, 3-2
manual, 3-3, 3-5
Speed reference, see also
Draw Gain Percentage (P016)
Jog Speed Reference (P.020)
Maximum Speed (P.004)
Minimum Speed (P.003)
Terminal Strip Speed Reference Source
(P.008)
Speed regulation
programming the drive for, 4-68
switching between torque and speed, 4-16
Speed Regulator Integral Gain (U.013), 4-76
Speed Regulator Proportional Gain (U.012), 4-75
Speed setpoint, see Speed Reference
Start-up procedures
vector (FVC and SVC), 2-1 to 2-37
volts/hertz, 1-1 to 1-24
Stop Type (P.025), 4-29
STOP/RESET Key Disable (P.055), 4-47
Stopping the drive, see
DC Braking Enable (H.005)
Jog Ramp Decel Time (P.022)
Option Port: Communication Loss Response
(P.062)
Stop Type (P.025)
Terminal Strip Analog Input Configure (P.011)
Terminal Strip Digital Inputs Configure (P.007)
Super Remote Meter Interface board, see Remote
Meter Interface board
SVC Flux Current Regulator Gain (U.032), 4-85
SVC Slip Adjust (U.030), 4-84
SVC Sync Direction (U.031), 4-85
SVC,
see Sensorless Vector Control
Sync Direction (H.016), 4-62
T
Terminal Strip Analog Input Configure (P.011), 4-19
Terminal Strip Analog Input Gain (P.010), 4-19
Terminal Strip Analog Input Offset (P.009), 4-18
Terminal Strip Analog Output Source (P.012), 4-21
Terminal Strip Digital Inputs Configure
(P.007), 4-14
Terminal Strip Speed Reference Source
(P.008), 4-17
Terminal strip, see
Control Source (P.000)
Function Loss Response (P.026)
Output Relay Configuration (P.013)
Torque Reference Source (U.000)
Trim Reference Source (P.014)
Thermal overload, see Motor Overload
Torque Boost Voltage (H.003), 4-56
Torque Reference Source (U.000), 4-68
Torque regulation
programming the drive for, 4-68
switching between torque and speed, 4-16
Torque Regulator Integral Gain (U.015), 4-77
Torque Regulator Proportional Gain (U.014), 4-76
Torque Self-Tune Enable (U.008), 4-74
Torque Self-Tune Result (U.009), 4-75
Trim Gain Percentage (P.015), 4-24
Trim Reference Source (P.014), 4-23
U
U parameters, 4-68 to 4-90
default settings, E-4
listed alphabetically, A-3
V
Vector parameters, 4-68 to 4-90
default settings, E-4
listed alphabetically, A-3
Vector regulation
description, H-1
programming the drive for, 4-16
selecting, see Volts/Hertz or Vector Regulation
(P.048)
start-up procedures, 2-1 to 2-37
Volts/Hertz Curve Type (H.018), 4-64
Volts/Hertz or Vector Regulation (P.048), 4-40
Volts/Hertz parameters, 4-55 to 4-67
default settings, E-3
listed alphabetically, A-2
Volts/Hertz regulation
description, H-1
selecting, see Volts/Hertz or Vector Regulation
(P.048)
start-up procedures, 1-1 to 1-24
Z
Zero Speed Hold Time (U.025), 4-82